Barco 9200 owner manual Controlling, How to Use the RCU?, Projector Address

Page 23

Controlling

6CONTROLLING

The projector can be controlled with a. The RCU

b. The hardwired RCU (cable is not included) c. The local keypad.

Controlling the projector with the RCU and the hardwired RCU is equal.

How to Use the RCU?

a) Point the front of the RCU to the reflective screen surface.

Ceiling

IR sensor

Screen

RCU

c)Point the front of the RCU directly at one of the IR sensors of the projector.

IR sensor

IR sensor

0 I

Table

Rear of projector

Front of projector

45°		45°	45°		45°
9	0
7	8	RCU	9	0
5	6		9	0
3	4		5 6
			7	8	RCU
1	2		3	4	RCU
			1 2

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if there are obstacles between the remote control unit and the projector IR sensor.

b) RCU used in a hardwired configuration.

0 I
			PROJECTOR MODE:
			GREEN - OPERATION	DIAGNOSTICS
	RS 232 IN	COMMUNICATIONPORT	RED - STANDBY	IR-ACKNOWLEDGED	CODE	IR-RECEIVER
RS232 OU T	RS 232 IN	(800-PERIPHERALS)	REMOTE
				IR-RECEIVED
						On
						2791098

Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the front panel of the projector labelled 'REMOTE'.

Projector Address

a. Software Set up of the Projector Address.

See 'Change projector address' in chapter 'Service mode'.

b. How to Control the Projector or Projectors.

Every projector requires an individual address between 0 and 255 which can be set in the Service mode.

When the address is set, the projector can be controlled now :

-RCU for addresses between 0 and 9.

-Computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.

Note : A projector will respond to a RCU set to an address of '0' regardless of what address is set in the projector itself.

c. Using the RCU.

Before using the RCU, its is necessary to enter the projector address into the RCU (only when that address is between 0 and 9). The projector with the corresponding address will listen to that specific RCU.

When address 0, <zero> is programmed into the RCU, every projec- tor, without exception will listen to the commands given by this RCU.

5975967 BARCOGRAPHICS 9200 221297		6-1

Image 23

Contents Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 11-1 10-110-2 10-4Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines RGB Analog with TRI-LEVEL Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with Standard Sync Sync on Green orFront Panel Terminology ControlLocal keypad Remote controlRC operating indication lights up when a button on Control disc Key on RCU or + and keys cursorFront/table, front/ceiling, rear/table and rear/ceiling Actual selected configuration will be highlightedInstallation ConfigurationInstallation Set Up Fuses Power mains cord connectionSwitching on ConnectionsInput connections Switching to stand-bySwitching off Lamp Run Time269,2VIDEO,1387 Video/S-video input moduleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleRGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computerConnecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Point the front of the RCU to the reflective screen surface How to Use the RCU?Controlling Projector AddressPicture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Adjustment Mode Start UP of the Adjustment ModeStart up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Edit file adaptation menu will be displayed File ServiceLoad File Edit FileHow to find the correct values for the displayed item? Example for clamp position trailing Copy RenameCopy RenameFile Options Picture TuningDelete Comparison with the green color value Color TemperatureSync slow/fast Still VideoSize GammaGeometry ShiftBlanking Side KeystoneBlanking Side KeystoneOptions Input Slots Starting up the Installation ModeConvergence ConvergenceRED on Green Internal Patterns ConfigurationBarcographics 9200 11-1 Service ModeStarting up the Service Mode ServiceIdentification IdentificationHow to enable or disable the password function ? Change PasswordChange Baudrate PC How to change the password ?Change Language Change Projector AddressBarcographics 9200 11-5 Reset Lamp RuntimeLamp Power Lamp Run Time HistoryI2C diagnosis Panel AdjustmentsPreset Input Balance Hz TrackingStandard Source SET UP Files 640 X 55,370 24,370 21,060 864 440 400 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 832 X 74,550 49,722 57,280 1152 667 624Lenses Focusing the lensLens Cleaning Procedure Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725