Barco 9200 owner manual Gamma, Geometry, Shift, Size

Page 34

Random Access Adjustment Mode

Gamma

With the gamma correction adjustment, it is possible to choose between higher color saturation (lower image values) and softer colors (higher gamma values).

To change the gamma value, highlight Gamma by pushing the control disc up or down and press ENTER.

PICTURE TUNING

SYNC [SLOW]

STILL VIDEO [ON]

COLOR TEMPERATURE

GAMMA

GAMMA = 2.2

3

Geometry

Highlight Geometry by pushing the control disc up or down and press ENTER to select the geometry selection menu.

The following adjustment are possible :

•horizontal and vertical image shift.

•horizontal and vertical image size

•side keystone (only necessary if the projector is mounted at a non standard projection angle).

•blanking

•options

The following ways are possible to adjust a geometry function :

•using the control disc to adjust or

•entering the value with the digit keys. Therefore, press ENTER to select the indicated value and enter the desired value with the digit keys. Press ENTER to confirm the entered value.

Shift

Highlight Shift by pushing the control disc up or down and press

ENTER.

The image can be shifted in a horizontal or vertical direction. Push the control disc up or down to shift the image in a vertical direction. Push the control disc to the right or to the left to shift the image in a horizontal direction. The default value for the shift is 0.

Shifting in a vertical direction : when the shift value is positive, the image is shifted upwards, when the value is negative, the image is shifted downwards.

Shifting in a horizontal direction : when the shift value is positive, the image is shifted to the right, when the value is negative, the image is shifted to the left.

Size

Highlight Size by pushing the control disc up or down and press ENTER to select.

The size can be adjusted in a vertical or horizontal way. When adjusting the vertical size,

The upper side of the image is fixed (table and ceiling mounted configurations) and only the lower side can be moved to its exact position.

When adjusting the horizontal size, the left side of the image is fixed and only the right side can be moved to its exact position.

RANDOM ACCESS

ADJUSTMENT MODE

FILE SERVICE

PICTURE TUNING

GEOMETRY

Select with

or

 

then <ENTER>

 

<EXIT> to

GEOMETRY

 

 

SHIFT

 

SIZE

 

SIDE KEYSTONE

 

BLANKING

 

OPTIONS

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

OPTIONS

Select with

or

then <ENTER>

<EXIT> to

return.

GEOMETRY

SHIFT

SIZE

SIDE KEYSTONE

BLANKING

OPTIONS

Select with

or

then <ENTER>

<EXIT> to

return.

Fixed sides

Horizontal size

adjustment

Vertical size adjustment

Example for table mount configuration

8-8

 

5975967 BARCOGRAPHICS 9200 030798

 

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-4 10-110-2 11-1Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines RGB Analog with Standard Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyControl disc Key on RCU or + and keys cursor Remote controlRC operating indication lights up when a button on Local keypadConfiguration Actual selected configuration will be highlightedInstallation Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Connections Power mains cord connectionSwitching on FusesLamp Run Time Switching to stand-bySwitching off Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector Projector Address How to Use the RCU?Controlling Point the front of the RCU to the reflective screen surfaceHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Edit File File ServiceLoad File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename RenameCopy CopyDelete Picture TuningFile Options Still Video Color TemperatureSync slow/fast Comparison with the green color valueShift GammaGeometry SizeSide Keystone Side KeystoneBlanking BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Service ModeStarting up the Service Mode Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?Change Projector Address How to change the password ?Change Language Change Baudrate PCLamp Run Time History Reset Lamp RuntimeLamp Power Barcographics 9200 11-5Hz Tracking Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files 832 X 74,550 49,722 57,280 1152 667 624 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 640 X 55,370 24,370 21,060 864 440 400Lens Cleaning Procedure Focusing the lensLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725
Top Page Image Contents