Barco 9200 owner manual RGB Analog Input Module

Page 18

Connections

RGB Analog Input Module.

RGB analog input terminals with separate Horizontal and Vertical sync inputs(RGB-HV), with Composite sync input(RGB-S) or with Sync signals on green(RGsB).

						PROJECTOR MODE :
						GREEN - OPERATION	DIAGNOSTICS
RS232 OUT		RS 232IN	COMMUNICATIONPORT			RED - STANDBY	IR-ACKNOWLEDGED CODE		IR-RECEIVER
RS232 OUT		RS 232IN	(800-PERIPHERALS)			REMOTE

IR-RECEIVED

Always use an interface when a computer and local monitor have to be connected to the projector. Interfaces to be applied :

R

G

B

H

V

R

G

B

H/ C

V

R

G

B

H / C

V

9827910

On

Universal analog interface. Order number : R9826100.

RGB 120 MHz analog interface. Order number : R9826570.

VGA interface

Order number 120V : R9828079.

Order number 230V : R9828070 MAC interface

Order number 120V : R9828059

Order number 230V : R9828050 MAGIK interface

Order number 120V : R9828129 Order number 230V : R9828120

RGBS/RGsB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB

Blue : 0.7 Vpp ± 3 dB

Green : 0.7 Vpp ± 3 dB

1 Vpp ± 3 dB if sync on green Vert. sync : 1 Vpp to 4 Vpp ± 3 dB Hor. sync / Composite sync :

1 Vpp to 4 Vpp ± 3 dB

R	G	B	C	V	27910
On					27910
					98

All input signals are always 75 ohm terminated, even in the "not selected" mode.

RGB Input Selection :

Key in the corresponding slot number on the RCU or the local keypad.

Straps on Module Level :

Floating or non-floating input.

Red :	J3	: strap "yes" : non floating	strap "no" : floating
Green : J4		: strap "yes" : non floating	strap "no" : floating
Blue :	J5	: strap "yes" : non floating	strap "no" : floating
H/C :	J6	: strap "yes" : non floating	strap "no" : floating
V : J7 : strap "yes" : non floating			strap "no" : floating

Factory preset : strap "yes", non floating input

Sync selection : strap on module level.

J8 : see drawing

Factory preset : separate sync.

Sync selection on the Input Slots menu.

The horizontal sync input can be set as separate sync input or as separate sync + video input. To change this setting, press ENTER key to start up the Adjustment mode.

Red

Green

Blue

Vert. sync

Hor. sync or Composite sync

Non-Floating

Floating

5-4		5975967 BARCOGRAPHICS 9200 221297

Image 18

Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-4 10-110-2 11-1Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines RGB Analog with Standard Sync Sync on Green or Where to install the projector?How to install a projection lens? RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyControl disc Key on RCU or + and keys cursor Remote controlRC operating indication lights up when a button on Local keypadConfiguration Actual selected configuration will be highlightedInstallation Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Connections Power mains cord connectionSwitching on FusesLamp Run Time Switching to stand-bySwitching off Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorConnecting an IR Remote Receiver 800 to the projector Projector Address How to Use the RCU?Controlling Point the front of the RCU to the reflective screen surfaceHow to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Edit File File ServiceLoad File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename RenameCopy CopyPicture Tuning DeleteFile Options Still Video Color TemperatureSync slow/fast Comparison with the green color valueShift GammaGeometry SizeSide Keystone Side KeystoneBlanking BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Service ModeStarting up the Service Mode Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?Change Projector Address How to change the password ?Change Language Change Baudrate PCLamp Run Time History Reset Lamp RuntimeLamp Power Barcographics 9200 11-5Hz Tracking Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files 832 X 74,550 49,722 57,280 1152 667 624 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808640 X 74,996 68,846 57,280 832 918 870 640 X 55,370 24,370 21,060 864 440 400Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725