Barco 9200 owner manual Configuration, Internal Patterns

Page 40

Installation Mode

Blue on green convergence.

Use the control disc to highlight Blue on green and press ENTER to display the Blue on green test pattern.

Repeat the same procedure as for Red on green lines but read blue when red is indicated.

To check the result of the convergence adjustments, highlight Hatch and press ENTER. A hatch pattern will be displayed on the screen. ENTER : displays a hatch pattern.

EXIT : returns to the installation menu.

All lines must be displayed in white, if not so repeat the convergence adjustment procedure.

Configuration

Highlight "Configuration" by pushing the control disc up or down and press ENTER to select.

For more information, see Projector configuration in chapter 4 : 'Installation Set Up'.

Internal Patterns

The projector is equipped with different internal patterns which can be used for measurment purposes.

Highlight "Internal Patterns" by pushing the control disc up or down and press ENTER to display the Internal Pattern selection menu. The following test pattern are available :

-Color Bars

-Multiburst

-Checker Board

-Purity

-Page Char (one page with the same character)

-Alpha-numeric characters

Each pattern (except Purity) can be inverted by pressing ENTER. For Page Char, the next or previous character can be selected by pushing the control disc up or down.

To return to the normal pattern, press EXIT.

CONVERGENCE
GREEN
BLUE ON GREEN
RED ON GREEN
HATCH
Select with	or
then <ENTER>
<EXIT> to return.

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

INTERNAL PATTERNS

Select with or then <ENTER> <EXIT> to return.

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

INTERNAL PATTERNS

Select with	or
then <ENTER>
<EXIT> to	INTERNAL PATTERNS

COLOR BARS

MULTIBURST

CHECKER BOARD

PURITY

PAGE CHAR

ALPHA-NUMERIC CHARS

Select with or then <ENTER> <EXIT> to return.

9-4		5975967 BARCOGRAPHICS 9200 221297

Image 40

Contents Graphics Page Barco Projection Systems Date Rev Art. No 030798 R5975947Federal communication commission FCC statement Table of Contents 10-1 10-210-4 11-1Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines Where to install the projector? How to install a projection lens?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orControl Front Panel TerminologyRemote control RC operating indication lights up when a button onControl disc Key on RCU or + and keys cursor Local keypadActual selected configuration will be highlighted InstallationConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Power mains cord connection Switching onConnections FusesSwitching to stand-by Switching offLamp Run Time Input connectionsVideo/S-video input module 269,2VIDEO,1387RGB Analog Input Module Component Input Module 2032117B-Y S9,2,1387RGB3S/RG3sB Input Module Set up of the baud rate for communication with a computer See Change Baudrate PC in chapter Service modeConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector How to Use the RCU? ControllingProjector Address Point the front of the RCU to the reflective screen surfaceHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Start UP of the Adjustment Mode Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service File Service Load FileEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Rename CopyRename CopyDelete Picture TuningFile Options Color Temperature Sync slow/fastStill Video Comparison with the green color valueGamma GeometryShift SizeSide Keystone BlankingSide Keystone BlankingOptions Starting up the Installation Mode Input SlotsConvergence ConvergenceRED on Green Configuration Internal PatternsService Mode Starting up the Service ModeService Barcographics 9200 11-1Identification IdentificationChange Password How to enable or disable the password function ?How to change the password ? Change LanguageChange Projector Address Change Baudrate PCReset Lamp Runtime Lamp PowerLamp Run Time History Barcographics 9200 11-5Panel Adjustments Preset Input BalanceHz Tracking I2C diagnosisStandard Source SET UP Files KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808 640 X 74,996 68,846 57,280 832 918 870832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Lens Cleaning Procedure Focusing the lensLenses Lenses Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725