Barco 9200 owner manual Starting up the Installation Mode, Input Slots

Page 37

Installation Mode

9	INSTALLATION MODE

Starting up the Installation Mode

Push the control disc up or down to highlight Installation and then press ENTER.

ENTER continues to the Installation mode selection menu. EXIT returns to operational mode.

The following item can be selected in the Installation mode :

Input slots : to set up the input priority.

Convergence : to align the red, green and blue image.

Configuration : to set up the projector position.

Internal Patterns

Input Slots

Highlight Input Slots by pushing the control disc up or down and press

ENTER.

The internal system will scan the input slots and displays the result in the Input Slots menu.

Source	indication
Video or S-Video	Video[Video]
	Video[S-Video]
RGB analog	RGB-SS[CV] : separate sync is composite video
	signal on H/C input
	RGB-SS[CS or HS&VS] : separate sync is
	composite sync or horizontal and vertical
	sync
	RGB-SOG : sync on green
Component video	Component Video - SS : component video
	with separate sync
	Component Video - SOY : component video
	with sync on Y
	Component Video - 3LSS : component video
	with 3 level separete sync.
	Component Video - 3LSOY : component
	video with 3 level sync on Y.
RGB analog with
tri-level sync	RGB3L-SS : RGB with separate Tri level sync
	RGB3L-SOG : RGB with Tri level sync on
	green

If a RCVDS (switched on) or VS05 is connected to the projector, it will be also indicated on the menu by adding +800 peripheral. If no 800 peripheral indication is made on the menu, there are still two possi- bilities :

-no RCVDS or VS05 connected or

-RCVDS is switched off.

When a 800 peripheral is connected to the projector, the input slots are not accessible with the control disc to toggle their function.

ADJUSTMENT MODE

Select a path from below :

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

INTERNAL PATTERNS

Select with or then <ENTER> <EXIT> to return.

INSTALLATION

INPUT SLOTS

CONVERGENCE

CONFIGURATION

INTERNAL PATTERNS

Select with	or
then <ENTER>
<EXIT>	INPUT SLOTS

Slot Module Type (config)

1. RGB-SS [CV]

2. RGB-SOG

3. Video [Video]

4. Component Video

5975957 BARCOGRAPHICS 9200 221297		9-1

Image 37

Contents Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 10-2 10-110-4 11-1Projector dimensions Unpacking and DimensionsUnpacking Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orFront Panel Terminology ControlRC operating indication lights up when a button on Remote controlControl disc Key on RCU or + and keys cursor Local keypadInstallation Actual selected configuration will be highlightedConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Switching on Power mains cord connectionConnections FusesSwitching off Switching to stand-byLamp Run Time Input connections269,2VIDEO,1387 Video/S-video input moduleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleRGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computerConnecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector Controlling How to Use the RCU?Projector Address Point the front of the RCU to the reflective screen surfaceHow to Program an Address into the RCU? How to Display a Projector Address?Picture Controls with Direct Access Adjustment Mode Start UP of the Adjustment ModeStart up of the Adjustment Mode Starting up the Random Access Adjustment Mode Random Access Adjustment ModeFile Service Load File File ServiceEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Copy RenameRename CopyDelete Picture TuningFile Options Sync slow/fast Color TemperatureStill Video Comparison with the green color valueGeometry GammaShift SizeBlanking Side KeystoneSide Keystone BlankingOptions Input Slots Starting up the Installation ModeConvergence ConvergenceRED on Green Internal Patterns ConfigurationStarting up the Service Mode Service ModeService Barcographics 9200 11-1Identification IdentificationHow to enable or disable the password function ? Change PasswordChange Language How to change the password ?Change Projector Address Change Baudrate PCLamp Power Reset Lamp RuntimeLamp Run Time History Barcographics 9200 11-5Preset Input Balance Panel AdjustmentsHz Tracking I2C diagnosisStandard Source SET UP Files 640 X 74,996 68,846 57,280 832 918 870 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Lens Cleaning Procedure Focusing the lensLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725