Barco Reset Lamp Runtime, Lamp Run Time History, Lamp Power, Barcographics 9200 11-5

Page 45

Service Mode

The following baud rates are available :

-9600

-4800

-2400

-1200

-600

-300

-150

-75

The actual baud rate will be highlighted. To change the baud rate, push the control stick forward or backward and press ENTER to accept the new baud rate setting.

Reset Lamp Runtime

Reset lamp run time is only allowed when a new lamp is installed. Highlight Reset Lamp Run Time by pushing the control stick forward or backward and press ENTER to select.

When Reset Lamp Run Time is selected in the Service Mode selection menu, the following warning will be displayed :

Risk of electrical shock. Reset lamp run time is reserved to qualified service personnel.

If you are not qualified, press EXIT to cancel the reset operation.

Lamp Run Time History

To get an overview of the different lamp run times, highlight Lamp Run Time History by pushing the control stick forward or backward and press ENTER.

A listing with the lamp serial number and the corresponding run time will be displayed.

The actual installed lamp will be marked.

Press EXIT to return to the service mode selection menu.

Lamp Power

Highlight Lamp power by pushing the control stick forward or backward and press ENTER to toggle between 1500W and 1200W.

CHANGE BAUDRATE PC

9600

4800

2400

1200

600

 

300

 

150

 

75

 

Select with

or

<ENTER> to accept

<EXIT> to

return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP POWER : 1500W

MORE

Select with

or

then <ENTER>

<EXIT>

WARNING

 

 

-----------------------------------------------------

 

RISK OF

 

ELECTRICAL SHOCK

______________________________________________________________

 

RESET LAMP RUN TIME

 

is reserved to

 

qualified

 

service personnel

 

<ENTER> to accept

 

<EXIT> to return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJ. ADDRESS

CHANGE BAUDRATE PC

RESET LAMP RUNTIME

LAMP RUNTINE HISTORY

LAMP POWER : 1500W

MORE...

then <ENTER> LAMP RUNTIME HISTORY

<EXIT> to

 

 

 

Serial No

Runtime

 

-----------------------------------------------------

 

> 0111121

600 h

 

0110031

750 h

 

0110010

745 h

 

-----------------------------------------------------

 

<EXIT>

to return

SERVICE

 

IDENTIFICATION

 

CHANGE PASSWORD

 

CHANGE LANGUAGE

 

CHANGE PROJ. ADDRESS

 

CHANGE BAUDRATE PC

 

RESET LAMP RUNTIME

 

LAMP RUNTINE HISTORY

 

LAMP POWER : 1500W

 

MORE...

 

Select with

or

 

then <ENTER>

 

<EXIT> to

return.

 

5975947 BARCOGRAPHICS 9200 120297

 

11-5

 

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection SystemsFederal communication commission FCC statement Table of Contents 10-2 10-110-4 11-1Unpacking and Dimensions Projector dimensionsUnpacking Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green orFront Panel Terminology ControlRC operating indication lights up when a button on Remote controlControl disc Key on RCU or + and keys cursor Local keypadInstallation Actual selected configuration will be highlightedConfiguration Front/table, front/ceiling, rear/table and rear/ceilingInstallation Set Up Switching on Power mains cord connectionConnections FusesSwitching off Switching to stand-byLamp Run Time Input connections269,2VIDEO,1387 Video/S-video input moduleRGB Analog Input Module 2032117B-Y S9,2,1387 Component Input ModuleRGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computerConnecting a Rcvds 05 to the projector Connecting a VS05 to the projectorConnecting an IR Remote Receiver 800 to the projector Controlling How to Use the RCU?Projector Address Point the front of the RCU to the reflective screen surfaceHow to Display a Projector Address? How to Program an Address into the RCU?Picture Controls with Direct Access Adjustment Mode Start UP of the Adjustment ModeStart up of the Adjustment Mode Random Access Adjustment Mode Starting up the Random Access Adjustment ModeFile Service Load File File ServiceEdit File Edit file adaptation menu will be displayedHow to find the correct values for the displayed item? Example for clamp position trailing Copy RenameRename CopyPicture Tuning DeleteFile Options Sync slow/fast Color TemperatureStill Video Comparison with the green color valueGeometry GammaShift SizeBlanking Side KeystoneSide Keystone BlankingOptions Input Slots Starting up the Installation ModeConvergence ConvergenceRED on Green Internal Patterns ConfigurationStarting up the Service Mode Service ModeService Barcographics 9200 11-1Identification IdentificationHow to enable or disable the password function ? Change PasswordChange Language How to change the password ?Change Projector Address Change Baudrate PCLamp Power Reset Lamp RuntimeLamp Run Time History Barcographics 9200 11-5Preset Input Balance Panel AdjustmentsHz Tracking I2C diagnosisStandard Source SET UP Files 640 X 74,996 68,846 57,280 832 918 870 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400Focusing the lens Lens Cleaning ProcedureLenses Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connectedSource numbers 81 13873525&8-6285&6&725
Top Page Image Contents