Onkyo TX-SR701E, TX-SR601E instruction manual Connecting the remote zone Zone 2 speakers

Page 23

Connecting the remote zone (Zone 2) speakers

The TX-SR701/701E/601/601E allows you to listen to two separate input sources at the same time. This allows you to, for example, place speakers in two different rooms so that two or more people can enjoy two different kinds of music at the same time. The room where the TX-SR701/701E/601/601E is actually located is referred to as the main room while the separate room is referred to as the remote zone (Zone 2). In addition, the IR IN terminal of the TX- SR701/701E/601/601E allows you to control the TX-SR701/701E/ 601/601E from the remote zone (Zone 2) with the remote controller even though the remote zone is physically separated. The diagrams below show how to make the proper connections for the remote zone.

When using the ZONE 2 SPEAKERS terminals

You can connect the speakers for the remote zone (Zone 2) to the ZONE 2 SPEAKERS terminals.

When you connect the speakers to the ZONE 2 SPEAKERS terminals, set the “Hardware Config” setting to “Zone 2.” In this setting, while you use the remote zone (Zone 2), surround playback will not be available for the main room (2ch stereo playback only). When you are not using the Zone 2, 6.1-channel playback will be available for the main room.

Remote Zone (Zone 2)

Zone 2

Zone 2

Left speaker

Right speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 2 amplifier

 

 

Main Room

 

ZONE 2

 

Left (white)

LINE OUT

 

L

 

 

 

 

R

REMOTE

 

 

CONTROL

Right (red)

TX-SR701/701E/601/601E

Note:

The ZONE 2 out terminals of the TX-SR701/701E/601/601E are of a fixed output level.

Main Room

ZONE 2

SPEAKERS

L

R

Remote Zone (Zone 2)

Zone 2

 

Zone 2

Left

 

Right

speaker

speaker

 

 

 

 

 

 

 

 

When using the ZONE 2 PRE OUT terminals (TX-SR701/701E only)

You can connect the amplifier for the remote zone (Zone 2) to the ZONE 2 PRE OUT terminals and connect the remote zone speakers.

When you connect the speakers to the ZONE 2 SPEAKERS terminals, set the “Hardware Config” setting to “Zone 2.” In this setting, while you use the remote zone (Zone 2), surround playback will not be available for the main room (2ch stereo playback only). When you are not using the Zone 2, 6.1-channel playback will be available for the main room.

TX-SR701/701E/601/601E

Note:

Main Room

Remote Zone (Zone 2)

Zone 2

Zone 2

Left

Right

speaker

speaker

It is important to be aware of the speaker impedance (see page 31).

When using the ZONE 2 LINE OUT terminals

The ZONE 2 LINE OUT terminal is a constant output. Connect to the LINE input of the amplifier (CD, tape, etc.). Adjust the volume with the amplifier connected to the ZONE 2 LINE OUT terminal.

In this connection, whatever the “Hardware Config” setting is set to, 6.1 channel playback is always available for main room.

1.Connect the TX-SR701/701E/601/601E to the amplifier for the remote zone.

2.Connect the remote zone speaker cables to the speaker terminals on the amplifier.

TX-SR701/701E

ZONE 2 FRONT

SURR CENTER SURR BACK

 

(SB)

L

L

PRE OUT

 

R

R

 

SUB

 

WOOFER

 

Left (white)

 

Right (red)

Power amplifier

23

Image 23
Contents TX-SR701/701E TX-SR601/601E Avis Important Safety InstructionsPrecautions Contents Contents TX-SR701/701E Amplifier Features FeaturesUsing the remote controller Supplied accessoriesBefore using this unit Setting the voltage selector Worldwide models onlyTX-SR601E Front panel facilitiesTX-SR701E Front panel facilities Audio Selector button Sleep indicator Muting indicatorListening mode or digital input format indicators Tuning indicatorsRemote controller VOL button Remote controllerInput Selector buttons Light button RC-533M onlyVideo connection cable Coaxial cable Optical cable ConnectionsImproper connection Inserted completely Left white Audio connection cable Right redConnections Signal flow Connecting your audio componentsConnecting a compact disc player CD Connecting a turntable Phono TX-SR701/701E onlyflow of the video signals is as follows Connecting your video componentsConnecting a DVD Player with 5.1-Channel Output Connecting a DVD player DVD Connecting a DVD Player with 2-Channel L/R Audio OutputVideo output White Analog audio output R red Connecting a video cassette recorder VideoMonitor OUT Connecting a television monitor or projector Monitor OUT12V Trigger Zone 2 terminal Connecting video camera, etc. Video 4 InputPRE OUT TX-SR701/701E only IR Receiver Connecting block Remote Controller Main room From connecting block Mini plug cableTX-SR701/701E/601/601E Connecting Block IR Receiver Cabinet Signal flowWhen using the Zone 2 Line OUT terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 Speakers terminals When using the Zone 2 PRE OUT terminals TX-SR701/701E onlyDimmer function Power on/ready functionPower off function Direct change functionImportant points regarding speaker placement Connecting speakersStandard speaker setup for surround sound Speaker placementConnecting the surround back speakers TX-SR701/701E only Connecting speakersUsing the speaker cable labels Connecting a subwooferStrip away approx /8 inch 15 mm Wire insulation Connecting speakersConnecting the speaker cable Turning on the power from the remote controller Connecting the powerTurning on the power Assembling the AM loop antenna Connecting antennasConnecting the included antennas Connecting the AM antenna cableDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaSpeaker Configuration Configuring the speakersDisplaying the Main Menu TX-SR601/601E Configuring the speakersTX-SR701/701E Speaker Distance menu appears Calibrating the speaker levels Use the and cursor buttons to select Left Using the remote controller Press the Test buttonPress the Test button to complete the procedure Displaying the Main Menu and exiting the menu Buttons used for navigating through the menusPress the Tuner input source button Tuned in stereo Auto mode Band FrequencyListening to Radio Broadcasts Listening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationPTY program types in Europe What is RDS?Listening to RDS broadcasts European models only Performing a TP scan Preset RT/PTY/TPListening to RDS broadcasts European models only Displaying Radio Text RTBasic operation Master VolumeSelecting an Audio Component Tape Audio Selector Selecting the type of audio input signalRcvr Mode CH SEL Audio SEL Level Selecting an Audio ComponentChanging the display Temporarily changing the speaker output levelsTo change the display of the input source from Tape to MD Enjoying DVD multichannel audio playback Using the sleep time remote controller onlyListening with headphones Temporarily turning off the sound Switching the displayListening Modes Listening Modes Re-EQ Selecting a listening mode TX-SR701/701ETX-SR701/701E Listening mode buttons TipWhile playing back Analog/PCM sources Re-EQ function for movies TX-SR701/701E onlyCine Fltr Selecting a listening mode TX-SR601/601ETX-SR601/601E Listening mode buttons Press the Cine Fltr button on the remote controller Digital Input Input SetupSetup Procedure Select the desired input source Component Video Input SetupIntelliVolume F. Mono source For e. PCM fs 96kHz source g. D. F. Mono sourceAnalog/PCM/D. F ch source Digital Format sourceTo display the Hardware Config menu Hardware SetupHardware Config To display the Preference menu PreferencePreference Audio Adjust Audio AdjustSetup Procedure Press the Audio Adjust button Audio Adjust Dialog Enhance Front ExpanderVirtual Surr Level Enjoying music in the remote zone Using the buttonsAdjusting the volume for the remote zone Recording a source different from that you are listening to RecordingRecording the input source REC OUT selector REC OUT OFFRecording both the audio and video RecordingVOL Using remote controllerCalling up a preset radio station Controlling an Onkyo cassette tape deckControlling an Onkyo DVD player Using remote controllerDVD Mode Press the DVD Mode buttonOn Standby CD Mode DiscPress the CD Mode button Controlling an Onkyo CD playerREC Record SAT/MD ModePress the SAT/MD Mode button Controlling an Onkyo MD recorderDisplay When entering the code of Onkyo DVD playersEntering a pre-programming code Learning a pre-programming codePre-programming codes Entering a pre-programming codeCable Mode Cable Mode Operating your programmed remote controllerDVD Mode DVD Player Mode SAT Mode Satellite Tuner ModeVCR Mode VOL TV/VCR Muting Operating your programmed remote controllerVCR Mode VCR Mode TV Mode TV ModeMacro 1 Macro Programming procedureLight Press and release the same button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againExecuting the macro Using the macro functionProgramming the macro Press the Macro 1 or 2 button again Using the macro functionErasing all commands and macros that have been programmed Erasing a macro from the Macro 1 or 2 buttonTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Amplifier Section Specifications TX-SR701/701EAmplifier Section Tuner Section Specifications TX-SR601/601EOnkyo Europe Electronics GmbH Onkyo U.S.A. CorporationPage Page Page Page Page Page