Enjoying music in the remote zone

ZONE 2 indicator											ON/STANDBY
	OFF
							AUDIO		MASTER VOLUME
							ADJUST SETUP	RETURN
STANDBY/ON
							TUNING
							PRESET
POWER
		STANDBY
ON OFF											LEVEL /
				LISTENING MODE							LEVEL /
REC OUT ZONE 2	OFFLEVEL	DISPLAY RT/PTY/TP	STEREO	SURROUND THX	DSP	MEMORY	FM MODE	ENTER
PHONES	DIRECT/	AUDIO	VIDEO 2 VIDEO 3	VIDEO 4					VIDEO 4 INPUT
	PURE AUDIO	SELECTORDVD VIDEO 1	VIDEO 2 VIDEO 3	VIDEO 4	TAPE	TUNERCD	PHONO
	PURE AUDIO
		VCR 1	VCR 2				DIGITAL		S VIDEO	VIDEO L AUDIO R	INPUT SELECTOR
							DIGITAL		S VIDEO	VIDEO L AUDIO R

											buttons
ZONE 2				Input source buttons							ZONE 2
ZONE 2											ZONE 2

Using the buttons

1.Press the ZONE 2 button.

2.Select an input source.

After pressing the ZONE 2 button, you must press an input source button within 5 seconds. The ZONE 2 indicator lights.

Ex.: When the CD button is pressed.

To select the same source for the remote zone that is selected for the main zone, press the ZONE 2 button again until “Zone2Sel:SOURCE” appears in the display.

•When “Zone2Sel:Off” is displayed, the output to the remote zone is turned off.

•When you are not using the remote zone (Zone 2), press the OFF button to turn off the ZONE 2 indicator.

Notes:

•If a sleep time is set with the SLEEP button, the output to the remote zone will also turn off when the sleep time elapses.

•If the source for the main zone is selected as the source for the remote zone and the source for the main zone is changed, then the source for the remote zone will change as well.

•The ZONE 2 terminal is an analog output. Digital signals are not output. If no sound is heard from the selected input source, check if the component is connected to the analog inputs.

•If the REC OUT button is pressed in the main room while someone is using the system in the remote zone, the Zone 2 function will be deactivated and the source will turn off in the remote zone.

•If you select FM (or AM) with the TUNER input source button when the source for the remote zone (Zone 2) is set to AM (or FM), the output for the remote zone also changes to FM (or AM).

•When you are using the remote zone (Zone 2), system operation will not work.

•In the remote zone, you can only play the source in the 2- channel mode. You cannot play the source in the remote zone in the surround mode.

Using the remote controller

With the TX-SR701/701E/601/601E in the standby state, turn on the output to the remote zone (Zone 2):

After pressing the ZONE 2 button, press the ON button within 5 seconds. The ZONE 2 indicator lights.

To turn off output to the remote zone (Zone 2), press the ZONE 2 button and then the STANDBY button within 5 seconds.

Select an input source:

After pressing the ZONE 2 button, press an input source button within 5 seconds.

If tuner is selected with the TUN button, you can use the CH button to select a preset radio station.

Note:

After you press the ZONE 2 button on the remote controller, the ZONE 2 indicator on the TX-SR701/701E/601/601E ﬂashes for ﬁve seconds. During this time, you will not be able to perform operations in the main zone using the remote controller.

Adjusting the volume for the remote zone

When the remote zone (Zone 2) speakers are connected to the ZONE 2 SPEAKERS terminals, or to an ampliﬁer connected to the ZONE 2 PRE OUT terminals, adjust the volume as shown below.

Press the LEVEL / buttons on the front panel.

Adjusting the volume (using the remote controller):

After pressing the ZONE 2 button, the ZONE 2 indicator on the TX-SR701/701E/601/601E will ﬂash for 5 seconds. During this time press the LEVEL / button.