Onkyo TX-SR701E, TX-SR601E Using the macro function, Programming the macro, Executing the macro

Page 73

Using the macro function

What is the macro function?

A macro function enables you to program a series of button operations (up to 16) on the remote controller into a single button. The series of operations are then called a macro. For example, to play a compact disc player connected to the TX-SR701/701E/601/

601E normally, you must perform the following steps:

1.Press the RCVR MODE button.

2.Press the ON button.

3.Press the CD (INPUT SELECTOR) button.

4.Press the CD MODE button.

5.Press the playback () button.

By using the macro function, you can perform the above five operations by only pressing one button.

 

SEND/LEARN

 

indicator

ON

 

MACRO 1

MACRO 2

RCVR MODE

MODE buttons

 

CD MODE

 

(CD playback)

CD (INPUT SELECTOR)

Tips:

If you erase or change the command of a button programmed in the macro, that operation of that button will no longer work in the macro. In this case, it will be necessary for you to reprogram the macro in order to avoid incorrect operation.

The codes programmed into the macro will be transmitted at an interval of 0.5 seconds. However, some devices may not be able to complete one operation in 0.5 seconds and may miss the next code. In this case, after pressing one operation button, you can press the same MODE button again before pressing the next operation button to add another 0.5 seconds between the two operations.

Programming the macro

With the macro function, you can program a series of button operations as a macro into the MACRO button so the macro can be executed with just one touch. Note that for the macro function, only one macro can be programmed. For example, to program the macro described above on this page for the MACRO button, perform the steps given below.

1.Press and hold down any one of the seven MODE buttons, press the MACRO 1 (or 2) button, and then release both buttons.

When you press the MODE button, it lights and the SEND/ LEARN indicator lights. When you press the MACRO 1 (or 2) button, the indicator turns off. When you release the buttons, the indicator flashes briefly and then lights again.

2.Press the operation buttons you wish to program in order (in this case, press RCVR MODE ON CD (INPUT SELECTOR) CD MODE playback () button).

When you press each button, the SEND/LEARN indicator turns off. When you release the button, the indicator lights.

3.Press the MACRO 1 (or 2) button to complete the procedure.

The SEND/LEARN indicator slowly flashes twice.

4.Check to see if the macro has been properly programmed.

Notes:

You may program up to 16 button operations into the macro function. If you try to program a 17th operation, it will be ignored, and programming is stopped.

If the SEND/LEARN indicator quickly flashes three times and turns off, then the remote controller has exited the programming mode because either you have made a mistake during programming or a time-out has occurred because no button has been pressed. Resume from Step 1.

Executing the macro

Perform the procedure below to execute the macro that you have programmed into the remote controller. After programming the macro, you should always run it at least once to make sure that it has been programmed properly.

Point the remote controller at the TX-SR701/701E/601/ 601E and press the MACRO 1 (or 2) button.

It may take a while for the macro to finish transmitting, so be sure to continue pointing the remote controller at the device until the SEND/LEARN indicator turns off.

73

Image 73
Contents TX-SR701/701E TX-SR601/601E Avis Important Safety InstructionsPrecautions Contents Contents TX-SR701/701E Amplifier Features FeaturesBefore using this unit Supplied accessoriesSetting the voltage selector Worldwide models only Using the remote controllerTX-SR701E Front panel facilitiesTX-SR601E Front panel facilities Audio Selector button Listening mode or digital input format indicators Muting indicatorTuning indicators Sleep indicatorRemote controller Input Selector buttons Remote controllerLight button RC-533M only VOL buttonImproper connection Inserted completely ConnectionsLeft white Audio connection cable Right red Video connection cable Coaxial cable Optical cableConnections Connecting a compact disc player CD Connecting your audio componentsConnecting a turntable Phono TX-SR701/701E only Signal flowConnecting a DVD Player with 5.1-Channel Output Connecting your video componentsflow of the video signals is as follows Connecting a DVD player DVD Connecting a DVD Player with 2-Channel L/R Audio OutputVideo output White Analog audio output R red Connecting a video cassette recorder VideoMonitor OUT Connecting a television monitor or projector Monitor OUTPRE OUT TX-SR701/701E only Connecting video camera, etc. Video 4 Input12V Trigger Zone 2 terminal TX-SR701/701E/601/601E Connecting Block IR Receiver From connecting block Mini plug cableCabinet Signal flow IR Receiver Connecting block Remote Controller Main roomWhen using the Zone 2 Speakers terminals Connecting the remote zone Zone 2 speakersWhen using the Zone 2 PRE OUT terminals TX-SR701/701E only When using the Zone 2 Line OUT terminalsPower off function Power on/ready functionDirect change function Dimmer functionStandard speaker setup for surround sound Connecting speakersSpeaker placement Important points regarding speaker placementUsing the speaker cable labels Connecting speakersConnecting a subwoofer Connecting the surround back speakers TX-SR701/701E onlyConnecting the speaker cable Connecting speakersStrip away approx /8 inch 15 mm Wire insulation Turning on the power Connecting the powerTurning on the power from the remote controller Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkageDisplaying the Main Menu Configuring the speakersSpeaker Configuration TX-SR701/701E Configuring the speakersTX-SR601/601E Speaker Distance menu appears Calibrating the speaker levels Press the Test button to complete the procedure Using the remote controller Press the Test buttonUse the and cursor buttons to select Left Displaying the Main Menu and exiting the menu Buttons used for navigating through the menusListening to Radio Broadcasts Tuned in stereo Auto mode Band FrequencyPress the Tuner input source button Selecting a preset radio station Presetting a radio stationErasing a preset radio station Listening to Radio BroadcastsListening to RDS broadcasts European models only What is RDS?PTY program types in Europe Listening to RDS broadcasts European models only Preset RT/PTY/TPDisplaying Radio Text RT Performing a TP scanSelecting an Audio Component Master VolumeBasic operation Rcvr Mode CH SEL Audio SEL Level Selecting the type of audio input signalSelecting an Audio Component Tape Audio SelectorTo change the display of the input source from Tape to MD Temporarily changing the speaker output levelsChanging the display Listening with headphones Using the sleep time remote controller onlyEnjoying DVD multichannel audio playback Temporarily turning off the sound Switching the displayListening Modes Listening Modes TX-SR701/701E Listening mode buttons Selecting a listening mode TX-SR701/701ETip Re-EQWhile playing back Analog/PCM sources Re-EQ function for movies TX-SR701/701E onlyTX-SR601/601E Listening mode buttons Selecting a listening mode TX-SR601/601ECine Fltr Press the Cine Fltr button on the remote controller Setup Procedure Select the desired input source Input SetupDigital Input IntelliVolume Input SetupComponent Video Analog/PCM/D. F ch source For e. PCM fs 96kHz source g. D. F. Mono sourceDigital Format source F. Mono sourceHardware Config Hardware SetupTo display the Hardware Config menu Preference PreferenceTo display the Preference menu Setup Procedure Press the Audio Adjust button Audio AdjustAudio Adjust Audio Adjust Virtual Surr Level Front ExpanderDialog Enhance Adjusting the volume for the remote zone Using the buttonsEnjoying music in the remote zone Recording the input source REC OUT selector RecordingREC OUT OFF Recording a source different from that you are listening toRecording both the audio and video RecordingCalling up a preset radio station Using remote controllerControlling an Onkyo cassette tape deck VOLDVD Mode Using remote controllerPress the DVD Mode button Controlling an Onkyo DVD playerPress the CD Mode button CD Mode DiscControlling an Onkyo CD player On StandbyPress the SAT/MD Mode button SAT/MD ModeControlling an Onkyo MD recorder REC RecordEntering a pre-programming code When entering the code of Onkyo DVD playersLearning a pre-programming code DisplayPre-programming codes Entering a pre-programming codeDVD Mode DVD Player Mode Operating your programmed remote controllerSAT Mode Satellite Tuner Mode Cable Mode Cable ModeVCR Mode VCR Mode Operating your programmed remote controllerTV Mode TV Mode VCR Mode VOL TV/VCR MutingLight Programming procedureMacro 1 Macro Erasing all the commands programmed under a Mode button Erasing the programmed command from one buttonPress and release the same Mode button again Press and release the same button againProgramming the macro Using the macro functionExecuting the macro Erasing all commands and macros that have been programmed Using the macro functionErasing a macro from the Macro 1 or 2 button Press the Macro 1 or 2 button againTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Amplifier Section Specifications TX-SR701/701EAmplifier Section Tuner Section Specifications TX-SR601/601EOnkyo Europe Electronics GmbH Onkyo U.S.A. CorporationPage Page Page Page Page Page