Onkyo TX-SR701E, TX-SR601E Power on/ready function, Direct change function, Power off function

Connections

AC OUTLETS

The TX-SR701/701E/601/601E is equipped with AC mains outlets for connecting the power cords from other devices so that their power is supplied through the TX-SR701/701E/601/601E. By doing this, you can leave the connected device turned on and have the STANDBY/ON button on the TX-SR701/701E/601/601E turn on and off the device together with the TX-SR701/701E/601/601E.

The shape, number, and total capacity of the AC outlets may differ depending on the area of purchase.

Caution:

Make sure that the total capacity of the components connected to the TX-SR701/701E/601/601E does not exceed the capacity that is printed on the rear panel (e.g., TOTAL 120W).

AC OUTLETS

	AC OUTLETS
	AC 120V 60 Hz
	SWITCHED
	TOTAL 120W 1A MAX.
AC 230-240V 50 Hz
SWITCHED
TOTAL 100W MAX.
European and	USA and Canadian
some Asian models	models

REMOTE CONTROL

The terminal on the TX-SR701/701E/601/601E is for

connecting other Onkyo components equipped with the same terminal. When a component is connected to the terminal, it can be operated by the remote controller supplied with the TX-SR701/ 701E/601/601E. In addition, when you connect a component to the terminal, you can also perform the system operations given

below.

Power on/ready function

When the TX-SR701/701E/601/601E is in the standby state, if an

-connected component is turned on, the TX-SR701/701E/601/ 601E also turns on and the input source selected at the TX-SR701/ 701E/601/601E automatically switches to that component.

Be aware that this function will not work if the power cord for the - connected component is connected to the AC OUTLET on the TX- SR701/701E/601/601E, or if the TX-SR701/701E/601/601E has already been turned on.

Direct change function

When the play button is pressed at an -connected component, the input source selected at the TX-SR701/701E/601/601E automatically changes to that component.

Power off function

When the TX-SR701/701E/601/601E is placed in the standby state, all -connected components are also automatically put into the standby state.

Also, if you press the ON button on the TX-SR701/701E/601/601E remote controller while the TX-SR701/701E/601/601E is turned on,

all -connected components (DVD players, CD players, MD recorders, tuners, etc.) are also turned on.

Dimmer function

The Dimmer function (display brightness adjustment) of the TX- SR701/701E/601/601E can be used to synchronize the display

brightness on the connected device using the connection.

Caution:

If an MD recorder is connected to the TAPE jack on the TX-SR701/ 701E/601/601E, switch the Input Selector from TAPE to MD (see page 43).

TX-SR701/701E/601/601E

connector

Ex: Onkyo CD player

connector

Ex: Onkyo cassette tape deck

To connect components using the terminal, simply connect a

remote control cable from this terminal to the terminal of

the other component. An remote control cable with a 1/8-inch (3.5-mm) miniature two-conductor plug comes with every cassette tape deck, compact disc player, MD recorder, and DVD player that

has an terminal.

•When performing operations with -connected components

using the system, do not use the remote zone (Zone 2) .

•For remote control operation, the audio connection cables must also be connected.

•If a component has two terminals, you can use either one to connect to the TX-SR701/701E/601/601E. The other one can be used to daisy chain with another component.

•With Onkyo DVD players, you can enter the pre-program code so that you can operate the DVD player directly with the remote

controller without connecting the terminals (see page 67).

24