Allied Telesis AT-IFS802SP manual Hardware Installation, Installation Steps

Page 17

AT-IFS802SP-80 User Manual

13

Chapter 3 Hardware Installation

In this paragraph, we will describe how to install the 8 10/100TX + 2 10/100/1000T/SFP Combo with X-Ring L2 Managed Industrial Switch and the installation points attended to it.

3.1 Installation Steps

1.Unpack the Industrial switch

2.Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not screwed on the Industrial switch, please refer to DIN-Rail Mounting section for DIN-Rail installation. If users want to wall mount the Industrial switch, please refer to Wall Mount Plate Mounting section for wall mount plate installation.

3.To hang the Industrial switch on the DIN-Rail track or wall.

4.Power on the Industrial switch. Please refer to the Wiring the Power Inputs section for knowing the information about how to wire the power.The power LED on the Industrial switch will light up. Please refer to the LED Indicators section for indication of LED lights.

5.Prepare the twisted-pair, straight through Category 5 cable for Ethernet connection.

6.Insert one side of RJ-45 cable (category 5) into the Industrial switch Ethernet port (RJ-45 port) and another side of RJ-45 cable (category 5) to the network device’s Ethernet port (RJ-45 port), ex: Switch PC or Server.The UTP port (RJ-45) LED on the Industrial switch will light up when the cable is connected with the network device. Please refer to the LED Indicators section for LED light indication.

[note]

Make sure that the connected network devices support MDI/MDI-X. If it does not support, use the crossover category-5 cable.

7. When all connections are set and LED lights all show in normal, the installation is complete.

Image 17

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Front Panel Physical DimensionHardware Description Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortConsole Management CLI Management Login in the Console InterfaceExec Commands LevelWeb-Based Management System LoginAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesTftp Update FirmwareRestore Configuration System Event Log Backup ConfigurationSyslog Configuration System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority TOS Configuration Igmp ConfigurationCOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Static MAC Address Misc ConfigurationMAC Address Table MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface System Reboot Factory DefaultSave Configuration Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsLow IP PasswordHigh IP Subnet maskPortid Port Commands SetDuplex full half 101001000autoDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk ~61440 Spanning Tree Commands SetSeconds Time secondsTrueFalse Port PriorityAutoTrueFalse Commands Set Igmp-query auto Igmp enableIgmp-query force Show igmpStatic hwaddr Mac-address-tableFilter hwaddr Show mac-addressV1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-stringHost-address View NameExcludedIncluded RXTXBoth Sec Port IDWords Accept authorize Disable rejectFlashbackupcfg BackupRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set Failure No event authenticationNo event ring-topology ChangeStart time End time Sntp Commands SetMinute TimezoneDual Homing Port Ring Commands SetControl Port