Allied Telesis AT-IFS802SP manual IP Configuration

Page 32

28	AT-IFS802SP-80 User Manual

6.5 IP Configuration

The switch is a network device which needs to be assigned an IP address for being identified on the network. Users have to decide a means of assigning IP address to the switch.

•DHCP Client: Enable or disable the DHCP client function.When DHCP client function is enabled, the switch will be assigned an IP address from the network DHCP server.The default IP address will be replaced by the assigned IP address on DHCP server. After the user clicks Apply, a popup dialog shows up to inform the user that when the DHCP client is enabled, the current IP will lose and user should find the new IP on the DHCP server.

•IP Address:Assign the IP address that the network is using. If DHCP client function is enabled, this switch is configured as a DHCP client.The network DHCP server will assign the IP address to the switch and display it in this column.The default IP is 192.168.16.1 or the user has to assign an IP address manually when DHCP Client is disabled.

•Subnet Mask:Assign the subnet mask to the IP address. If DHCP client function is disabled, the user has to assign the subnet mask in this column field.

•Gateway:Assign the network gateway for the switch. If DHCP client function is disabled, the user has to assign the gateway in this column field.The default gateway is 192.168.16.254.

•DNS1:Assign the primary DNS IP address.

•DNS2:Assign the secondary DNS IP address.

• And then, click Apply

IP configuration interface

Image 32

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features IntroductionCSMA/CD Software Features Snmp MIBPackage Contents Front Panel Physical DimensionHardware Description Top View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortConsole Management Login in the Console Interface CLI ManagementCommands Level ExecSystem Login Web-Based ManagementAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsTftp Update FirmwareRestore Configuration System Event Log Backup ConfigurationSyslog Configuration System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority TOS Configuration Igmp ConfigurationCOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface Static MAC Address Misc ConfigurationMAC Address Table MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface System Reboot Factory DefaultSave Configuration Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands SetPassword Low IPHigh IP Subnet maskPort Commands Set PortidDuplex full half 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Spanning Tree Commands Set ~61440Seconds Time secondsTrueFalse Port PriorityAutoTrueFalse Commands Set Igmp enable Igmp-query autoIgmp-query force Show igmpMac-address-table Static hwaddrFilter hwaddr Show mac-addressAuthentication Password Privacy V1v2cv3v1v2cv3Strings Community Community-stringHost-address View NameExcludedIncluded RXTXBoth Sec Port IDWords Disable reject Accept authorizeBackup FlashbackupcfgRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set No event authentication FailureNo event ring-topology ChangeSntp Commands Set Start time End timeMinute TimezoneDual Homing Port Ring Commands SetControl Port