Allied Telesis AT-IFS802SP manual MAC Address Table, Misc Configuration, Static MAC Address

Page 71

AT-IFS802SP-80 User Manual

67

6.25.3 Misc Configuration

•Quiet Period: Set the period which the port doesn’t try to acquire a supplicant.

•TX Period: Set the period port waits for retransmit next EAPOL PDU during an authentication session.

•SupplicantTimeout: Set the period of time the switch waits for a supplicant response to an EAP request.

•Server Timeout: Set the period of time the switch waits for a server response to an authentication request.

•Max Requests: Set the number of authentication that must time-out before authentication fails and the authentication session ends.

•Reauth period: Set the period of time which clients connected must be re-authenticated.

•Click Apply .

802.1x Misc Configuration interface

6.26 MAC Address Table

Use the MAC address table to ensure the port security.

6.26.1 Static MAC Address

You can add a static MAC address that remains in the switch’s address table regardless of whether the device is physically connected to the switch.This saves the switch from having to re-learn a device’s MAC address when the disconnected or powered-off device is active on the network again.Via this interface, you can add / modify / delete a static MAC address.

Image 71

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Front Panel Physical DimensionHardware Description Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortConsole Management CLI Management Login in the Console InterfaceExec Commands LevelPreparing for Web Management System LoginWeb-Based Management About Web-based ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesTftp Update FirmwareRestore Configuration System Event Log Backup ConfigurationSyslog Configuration System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority TOS Configuration Igmp ConfigurationCOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Static MAC Address Misc ConfigurationMAC Address Table MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface System Reboot Factory DefaultSave Configuration Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsSubnet mask PasswordLow IP High IP101001000auto Port Commands SetPortid Duplex full halfDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Time seconds Spanning Tree Commands Set~61440 SecondsTrueFalse Port PriorityAutoTrueFalse Commands Set Show igmp Igmp enableIgmp-query auto Igmp-query forceShow mac-address Mac-address-tableStatic hwaddr Filter hwaddrCommunity-string Authentication Password PrivacyV1v2cv3v1v2cv3 Strings CommunityHost-address View NameExcludedIncluded RXTXBoth Sec Port IDWords Accept authorize Disable rejectFlashrestorecfg BackupFlashbackupcfg RestoreSystemLog, Smtp and Event Commands Set Change No event authenticationFailure No event ring-topologyTimezone Sntp Commands SetStart time End time MinuteDual Homing Port Ring Commands SetControl Port