Allied Telesis AT-IFS802SP manual System Event Log, Backup Configuration, Syslog Configuration

Page 36

32	AT-IFS802SP-80 User Manual

6.7.3 Backup Configuration

You can back up the current configuration from flash ROM to the TFTP server for the purpose of recovering the configuration later. It helps you to avoid wasting time on configuring the settings by backing up the configuration.

•TFTP Server IP Address:Type in the TFTP server IP.

•Backup File Name:Type in the file name.

•Click Apply

Backup Configuration interface

6.8 System Event Log

This page allows the user to decide whether to send the system event log, and select the mode which the system event log will be sent to client only, server only, or both client and server. What kind of event log will be issued to the client/server depends on the selection on the Event Configuration tab. There are five types of event—Device Cold Start, Device Warm Start,Authentication Failure, X-Ring Topology Change, and Port Event—available to be issued as the event log.

6.8.1Syslog Configuration

•Syslog Client Mode: Select the system log mode—Client Only, Server Only, or Both. ‘Client

Only’ means the system event log will only be sent to this interface of the switch, but on the other hand ‘Server Only’ means the system log will only be sent to the remote system log server with its IP assigned. If the mode is set in ‘Both’, the system event log will be sent to the remote server and this interface.

•System Log Server IP Address:When the ‘Syslog Mode’ item is set as Server Only/Both, the user has to assign the system log server IP address to which the log will be sent.

• Click Reload to refresh the event log displaying area.

•Click Clear to clear all the current event logs.

•Make sure the selected mode is correct, and click Apply to have the setting take effect.

Image 36

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features IntroductionCSMA/CD Software Features Snmp MIBPackage Contents Physical Dimension Hardware DescriptionFront Panel Top View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Console ManagementPin Assignment Login in the Console Interface CLI ManagementCommands Level ExecSystem Login Web-Based ManagementAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsUpdate Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface Factory Default Save ConfigurationSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands SetPassword Low IPHigh IP Subnet maskPort Commands Set PortidDuplex full half 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Spanning Tree Commands Set ~61440Seconds Time secondsPort Priority AutoTrueFalseTrueFalse Commands Set Igmp enable Igmp-query autoIgmp-query force Show igmpMac-address-table Static hwaddrFilter hwaddr Show mac-addressAuthentication Password Privacy V1v2cv3v1v2cv3Strings Community Community-stringView Name ExcludedIncludedHost-address RXTXBoth Port ID WordsSec Disable reject Accept authorizeBackup FlashbackupcfgRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set No event authentication FailureNo event ring-topology ChangeSntp Commands Set Start time End timeMinute TimezoneRing Commands Set Control PortDual Homing Port