Allied Telesis AT-IFS802SP manual Rate Limiting

Page 53

AT-IFS802SP-80 User Manual

49

6.17 Rate Limiting

You can set up every port’s bandwidth rate and frame limitation type.

•Ingress Limit Frame type: select the frame type that wants to filter.There are four frame types for selecting:

>All

>Broadcast/Multicast/Flooded Unicast

>Broadcast/Multicast

>Broadcast only

Broadcast/Multicast/Flooded Unicast, Broadcast/Multicast and Broadcast only types are only for ingress frames.The egress rate only supports All type.

Rate Limiting interface

•All the ports support port ingress and egress rate control. For example, assume port 1 is 10Mbps, users can set it’s effective egress rate is 1Mbps, ingress rate is 500Kbps.The switch performs the ingress rate by packet counter to meet the specified rate

>Ingress: Enter the port effective ingress rate (The default value is “0”).

>Egress: Enter the port effective egress rate (The default value is “0”).

•And then, click Apply to apply the settings

Image 53

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Front Panel Physical DimensionHardware Description Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortConsole Management CLI Management Login in the Console InterfaceExec Commands LevelWeb-Based Management System LoginAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesTftp Update FirmwareRestore Configuration System Event Log Backup ConfigurationSyslog Configuration System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority TOS Configuration Igmp ConfigurationCOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Static MAC Address Misc ConfigurationMAC Address Table MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface System Reboot Factory DefaultSave Configuration Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsLow IP PasswordHigh IP Subnet maskPortid Port Commands SetDuplex full half 101001000autoDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk ~61440 Spanning Tree Commands SetSeconds Time secondsTrueFalse Port PriorityAutoTrueFalse Commands Set Igmp-query auto Igmp enableIgmp-query force Show igmpStatic hwaddr Mac-address-tableFilter hwaddr Show mac-addressV1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-stringHost-address View NameExcludedIncluded RXTXBoth Sec Port IDWords Accept authorize Disable rejectFlashbackupcfg BackupRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set Failure No event authenticationNo event ring-topology ChangeStart time End time Sntp Commands SetMinute TimezoneDual Homing Port Ring Commands SetControl Port