Allied Telesis AT-IFS802SP manual Web-Based Management, About Web-based Management, System Login

Page 30

26	AT-IFS802SP-80 User Manual

Chapter 6 Web-Based Management

This section introduces the configuration and functions of the Web-Based management.

6.1 About Web-based Management

There is an embedded HTML web site residing in flash memory on CPU board of the switch, which offers advanced management features and allows users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer.

The Web-Based Management supports Internet Explorer 6.0 or later version.And, it is applied for Java Applets for reducing network bandwidth consumption, enhance access speed and present an easy viewing screen.

6.2 Preparing for Web Management

Before using the web management, install the industrial switch on the network and make sure that any one of the PCs on the network can connect with the industrial switch through the web browser.The industrial switch default value of IP, subnet mask, username and password are listed as below:

•IP Address: 192.168.1.1

•Subnet Mask: 255.255.255.0

•Default Gateway: 192.168.1.254

•User Name: manager

•Password: friend

6.3 System Login

1.Launch the Internet Explorer on the PC

2.Key in “http:// “+” the IP address of the switch”, and then Press “Enter”.

Image 30

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features IntroductionCSMA/CD Software Features Snmp MIBPackage Contents Physical Dimension Hardware DescriptionFront Panel Top View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Console Management Pin Assignment Login in the Console Interface CLI ManagementCommands Level ExecAbout Web-based Management System LoginWeb-Based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsUpdate Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface Factory Default Save ConfigurationSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands SetHigh IP PasswordLow IP Subnet maskDuplex full half Port Commands SetPortid 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Seconds Spanning Tree Commands Set~61440 Time secondsPort Priority AutoTrueFalseTrueFalse Commands Set Igmp-query force Igmp enableIgmp-query auto Show igmpFilter hwaddr Mac-address-tableStatic hwaddr Show mac-addressStrings Community Authentication Password PrivacyV1v2cv3v1v2cv3 Community-stringView Name ExcludedIncludedHost-address RXTXBoth Port ID WordsSec Disable reject Accept authorizeRestore BackupFlashbackupcfg FlashrestorecfgSystemLog, Smtp and Event Commands Set No event ring-topology No event authenticationFailure ChangeMinute Sntp Commands SetStart time End time TimezoneRing Commands Set Control PortDual Homing Port