Allied Telesis AT-IFS802SP manual Login in the Console Interface, CLI Management

Page 28

24	AT-IFS802SP-80 User Manual

5.3 Login in the Console Interface

When the connection between Switch and PC is ready, turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port:

Baud Rate: 9600 bps

Data Bits: 8

Parity: none

Stop Bit: 1

Flow control: None

Having finished the parameter settings, click ‘OK’.When the blank screen shows up, press Enter key to have the login prompt appears. Key in ‘manager’ (default value) for User name and “friend” for Password (use Enter key to switch), then press Enter and the Main Menu of console management appears..

5.4 CLI Management

The system supports the console management—CLI command.After you log in on to the system, you will see a command prompt.To enter CLI management interface, type in “enable” command.

CLI command interface

The following table lists the CLI commands and description.

Image 28

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features IntroductionCSMA/CD Software Features Snmp MIBPackage Contents Hardware Description Physical DimensionFront Panel Top View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Console Management Connecting to the Console PortPin Assignment Login in the Console Interface CLI ManagementCommands Level ExecSystem Login Web-Based ManagementAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsRestore Configuration Update FirmwareTftp Syslog Configuration Backup ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority COS Configuration Igmp ConfigurationTOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface MAC Address Table Misc ConfigurationStatic MAC Address MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface Save Configuration Factory DefaultSystem Reboot Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands SetPassword Low IPHigh IP Subnet maskPort Commands Set PortidDuplex full half 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Spanning Tree Commands Set ~61440Seconds Time secondsAutoTrueFalse Port PriorityTrueFalse Commands Set Igmp enable Igmp-query autoIgmp-query force Show igmpMac-address-table Static hwaddrFilter hwaddr Show mac-addressAuthentication Password Privacy V1v2cv3v1v2cv3Strings Community Community-stringExcludedIncluded View NameHost-address RXTXBoth Words Port IDSec Disable reject Accept authorizeBackup FlashbackupcfgRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set No event authentication FailureNo event ring-topology ChangeSntp Commands Set Start time End timeMinute TimezoneControl Port Ring Commands SetDual Homing Port