Allied Telesis AT-IFS802SP manual User Authentication, Port Statistics

Page 44

40	AT-IFS802SP-80 User Manual

6.12 User Authentication

Change web management login user name and password for the management security issue.

•User name:Type in the new user name (The default is ‘root’)

•Password:Type in the new password (The default is ‘root’)

•Confirm password: Re-type the new password

•And then, click Apply

User Authentication interface

6.13 Port Statistics

The following chart provides the current statistic information which displays the real-time packet transfer status for each port.The user might use the information to plan and implement the network, or check and find the problem when the collision or heavy traffic occurs.

•Port:The port number.

•Type: Displays the current speed of connection to the port.

•Link:The status of linking—‘Up’ or ‘Down’.

•State: It’s set by Port Control. When the state is disabled, the port will not transmit or receive any packet.

•Tx Good Packet:The counts of transmitting good packets via this port.

•Tx Bad Packet:The counts of transmitting bad packets (including undersize [less than 64 octets], oversize, CRC Align errors, fragments and jabbers packets) via this port.

•Rx Good Packet:The counts of receiving good packets via this port.

•Rx Bad Packet:The counts of receiving good packets (including undersize [less than 64 octets], oversize, CRC error, fragments and jabbers) via this port.

•Tx Abort Packet:The aborted packet while transmitting.

•Packet Collision:The counts of collision packet.

•Packet Dropped:The counts of dropped packet.

•Rx Bcast Packet:The counts of broadcast packet.

•Rx Mcast Packet:The counts of multicast packet.

•Click Apply button to clean all counts.

Image 44

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content Appendix B-Command Sets 21.3Page Hardware Features IntroductionCSMA/CD Software Features Snmp MIBPackage Contents Front Panel Physical DimensionHardware Description Top View LED Indicators LEDHardware Installation Installation StepsDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Cabling Gigabit Copper/SFP SFP combo portPage Network Application Ring ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortConsole Management Login in the Console Interface CLI ManagementCommands Level ExecSystem Login Web-Based ManagementAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration System configuration Dhcp ServerClient Entries Port and IP BindingsTftp Update FirmwareRestore Configuration System Event Log Backup ConfigurationSyslog Configuration System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Fault Relay Alarm Sntp ConfigurationPage Page IP Security User Authentication Port StatisticsPort Control Aggregator setting Port TrunkState Activity tab Lacp disabled Aggregator InformationLacp enabled Page State Activity Port Mirroring Rate Limiting Vlan configuration Port-based VlanVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rstp System Configuration Rapid Spanning TreePort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Configuration QoS Policy and Priority TypePort-based Priority TOS Configuration Igmp ConfigurationCOS Configuration Ring Page Lldp Configuration Security-802.1X/Radius Configuration802.1x System Configuration interface Static MAC Address Misc ConfigurationMAC Address Table MAC Filtering All MAC Addresses MAC Address Table-Multicast FilteringMulticast Filtering interface System Reboot Factory DefaultSave Configuration Troubles shooting Appendix A-RJ-45 Pin Assignment RJ-45 Pin Assignments10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic Appendix B-Command Sets System Commands SetPassword Low IPHigh IP Subnet maskPort Commands Set PortidDuplex full half 101001000autoState Enable DisableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Spanning Tree Commands Set ~61440Seconds Time secondsTrueFalse Port PriorityAutoTrueFalse Commands Set Igmp enable Igmp-query autoIgmp-query force Show igmpMac-address-table Static hwaddrFilter hwaddr Show mac-addressAuthentication Password Privacy V1v2cv3v1v2cv3Strings Community Community-stringHost-address View NameExcludedIncluded RXTXBoth Sec Port IDWords Disable reject Accept authorizeBackup FlashbackupcfgRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set No event authentication FailureNo event ring-topology ChangeSntp Commands Set Start time End timeMinute TimezoneDual Homing Port Ring Commands SetControl Port