Allied Telesis AT-IFS802SP manual Tftp, Update Firmware, Restore Configuration

Page 35

AT-IFS802SP-80 User Manual

31

6.7 TFTP

It provides the functions allowing the user to update the switch firmware via the Trivial File Transfer Protocol (TFTP) server. Before updating, make sure the TFTP server is ready and the firmware image is located on the TFTP server.

6.7.1Update Firmware

•TFTP Server IP Address:Type in your TFTP server IP.

•Firmware File Name:Type in the name of the firmware image file to be updated.

•Click Apply

Update Firmware interface

6.7.2 Restore Configuration

You can restore a previous backup configuration from the TFTP server to recover the settings. Before doing that, you must locate the image file on the TFTP server first and the switch will download back the flash image.

•TFTP Server IP Address:Type in the TFTP server IP.

•Restore File Name:Type in the correct file name for restoring.

•Click Apply

Restore Configuration interface

Image 35

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Front Panel Physical DimensionHardware Description Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortConsole Management CLI Management Login in the Console InterfaceExec Commands LevelPreparing for Web Management System LoginWeb-Based Management About Web-based ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesTftp Update FirmwareRestore Configuration System Event Log Backup ConfigurationSyslog Configuration System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority TOS Configuration Igmp ConfigurationCOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Static MAC Address Misc ConfigurationMAC Address Table MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface System Reboot Factory DefaultSave Configuration Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsSubnet mask PasswordLow IP High IP101001000auto Port Commands SetPortid Duplex full halfDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk Time seconds Spanning Tree Commands Set~61440 SecondsTrueFalse Port PriorityAutoTrueFalse Commands Set Show igmp Igmp enableIgmp-query auto Igmp-query forceShow mac-address Mac-address-tableStatic hwaddr Filter hwaddrCommunity-string Authentication Password PrivacyV1v2cv3v1v2cv3 Strings CommunityHost-address View NameExcludedIncluded RXTXBoth Sec Port IDWords Accept authorize Disable rejectFlashrestorecfg BackupFlashbackupcfg RestoreSystemLog, Smtp and Event Commands Set Change No event authenticationFailure No event ring-topologyTimezone Sntp Commands SetStart time End time MinuteDual Homing Port Ring Commands SetControl Port