Allied Telesis AT-IFS802SP manual Port Control

Page 45

AT-IFS802SP-80 User Manual

41

Port Statistics interface

6.14 Port Control

In Port control you can configure the settings of each port to control the connection parameters, and the status of each port is listed beneath.

•Port: Use the scroll bar and click on the port number to choose the port to be configured.

•State: Current port state.The port can be set to disable or enable mode. If the port state is set as ‘Disable’, it will not receive or transmit any packet.

•Negotiation: Auto and Force. Being set as Auto, the speed and duplex mode are negotiated automatically.When you set it as Force, you have to set the speed and duplex mode manually.

•Speed: It is available for selecting when the Negotiation column is set as Force. When the Negotiation column is set as Auto, this column is read-only.

•Duplex: It is available for selecting when the Negotiation column is set as Force. When the Negotiation column is set as Auto, this column is read-only.

•Flow Control: Whether or not the receiving node sends feedback to the sending node is determined by this item. When enabled, once the device exceeds the input data rate of another device, the receiving device will send a PAUSE frame which halts the transmission of the sender for a specified period of time.When disabled, the receiving device will drop the packet if too much to process.

•Security:When the Security selection is set as ‘On’, any access from the device which connects to this port will be blocked unless the MAC address of the device is included in the static MAC address table. See the segment of MAC Address Table—Static MAC Addresses.

•Click Apply to have the configuration take effect.

Image 45

Contents AT-IFS802SP Installation and User’s Guide Page Electrical Safety and Emissions Standards Page Preface Preface Content 21.3 Appendix B-Command SetsPage Introduction Hardware FeaturesCSMA/CD Snmp MIB Software FeaturesPackage Contents Physical Dimension Hardware DescriptionFront Panel Top View LED LED IndicatorsInstallation Steps Hardware InstallationDIN-Rail Mounting Wall Mount Plate Mounting Wiring the Power Inputs Wiring the Fault Alarm Contact Gigabit Copper/SFP SFP combo port CablingPage Ring Application Network ApplicationCoupling Ring Application Dual Homing Application Connecting to the Console Port Console ManagementPin Assignment CLI Management Login in the Console InterfaceExec Commands LevelWeb-Based Management System LoginAbout Web-based Management Preparing for Web ManagementSystem Information IP Configuration Dhcp Server System configurationPort and IP Bindings Client EntriesUpdate Firmware Restore ConfigurationTftp Backup Configuration Syslog ConfigurationSystem Event Log System Event Log-SMTP Configuration System Event Log Event Configuration Event Configuration interface Sntp Configuration Fault Relay AlarmPage Page IP Security Port Statistics User AuthenticationPort Control Port Trunk Aggregator settingState Activity tab Aggregator Information Lacp disabledLacp enabled Page State Activity Port Mirroring Rate Limiting Port-based Vlan Vlan configurationVlan Port Based interface 18.2 802.1Q Vlan 802.1Q Configuration Page Rapid Spanning Tree Rstp System ConfigurationPort Configuration Snmp Configuration Trap Configuration SNMPV3 Configuration QoS Policy and Priority Type QoS ConfigurationPort-based Priority Igmp Configuration COS ConfigurationTOS Configuration Ring Page Security-802.1X/Radius Configuration Lldp Configuration802.1x System Configuration interface Misc Configuration MAC Address TableStatic MAC Address MAC Filtering MAC Address Table-Multicast Filtering All MAC AddressesMulticast Filtering interface Factory Default Save ConfigurationSystem Reboot Troubles shooting RJ-45 Pin Assignments Appendix A-RJ-45 Pin Assignment10/100/1000Base-TX Pin outs 10/100/1000Base-TX Cable Schematic System Commands Set Appendix B-Command SetsLow IP PasswordHigh IP Subnet maskPortid Port Commands SetDuplex full half 101001000autoDisable State EnableTrunk Commands Set Vlan Commands Set Vlan 8021q trunk ~61440 Spanning Tree Commands SetSeconds Time secondsPort Priority AutoTrueFalseTrueFalse Commands Set Igmp-query auto Igmp enableIgmp-query force Show igmpStatic hwaddr Mac-address-tableFilter hwaddr Show mac-addressV1v2cv3v1v2cv3 Authentication Password PrivacyStrings Community Community-stringView Name ExcludedIncludedHost-address RXTXBoth Port ID WordsSec Accept authorize Disable rejectFlashbackupcfg BackupRestore FlashrestorecfgSystemLog, Smtp and Event Commands Set Failure No event authenticationNo event ring-topology ChangeStart time End time Sntp Commands SetMinute TimezoneRing Commands Set Control PortDual Homing Port