Omega Speaker Systems LCIC-WIM-BEN Appendix a I/O & the LED Display, General Notes about the I/O

Page 49

Appendix A: I/O & the LED Display

A.1 General Notes about the I/O

*The digital I/O is available on CONN6 (15 pin Dsub).

*Digital Outputs

The outputs are opto-isolated 300mA 50V solid state relays. When activated (status LED is on), they switch the OUTPUT x (x=1,2,3, or

4)to I/O VOLTAGE OV. Hence the load would normally be connected between OUTPUT x and the I/O VOLTAGE+.

*Digital Inputs

The digital inputs are designed to work with either npn or contact input devices. They are activated by an external device pulling INPUT x (x=1,2,3,or 4) down to I/O VOLTAGE OV.

To work in this way an external IO VOLTAGE+ (in the range 10-30V) must be present.

* Analog Output

The analog output signal is set by a 16 bit DAC and appears on pin12 of CONN6. The output is with respect to the LCIC_WIM board ground (not the I/O 0V). The board ground appears at

pin13 of CONN6. The analog output control is application dependent.

48

Image 49

Contents LCIC-WIM-BEN Servicing North America Table of Contents Programming your Application O & the LED Display AppendicesTrouble-shooting General Description IntroductionTypical Applications Installing the board in the PC Page After a while, you’ll have this display Click ‘Finish’ Run the setups of the LCIC-WIM utilities in the folders Setup & RunningUtilities Run a utilityGeneral Calibration UtilityThree stages are Show Data step Pseudo Calibration stepsFive calibration steps are Page Page Page Page Calibrations Library RestoreSave Parameters Calibration Efficiency CE Menu Bar Settings UtilityTools / Analog Output Tools / Baud Rate for SCI port Tools / General Setpoints Communication  The address setting takes effect only upon board resetPort Baud RateGet results immediately Activate Auto ZeroMax Zero Min ZeroPage Filter1 Filter2 Decimator FilteringFilling Definition Programming your Application CommandsGet a single reading RS485 Address selection, setting & reading Misc Summary of Weight & A/D Reading Commands Parameter Parameter Description Data Number Type ParametersBecomes effective only after a system reset either Calibration Name 32 characters max Start/Stop Communication LCIC-WIM ActiveXGetVariablerVariable Name VariablesCategory Variable Name Description Get Set Variables TableVariables Table cont’d AnalogOutputM = Manual, 1 = Auto Internal updates there will be a Parameter that needs no change FiltersFilteringLevel Integer Fast ModeTransmission sends blocks of information Stage How to work with the Fast Mode in VB using the ActiveX Interpreting the data in a block MiscGeneral Notes about the I/O Appendix a I/O & the LED DisplayDigital Inputs Analog OutputConnections Pin FunctionConnecting External Devices to the Inputs LCIC-WIM I/O & Analog Out LED Display Appendix B Scaling the Load Cell Input Appendix C Load Cell Connections Communication Parameters Appendix D USB, RS232 & RS485Baud Rate RS485 Activate address x x=1, 2, 3, …, 62, 63 RS485 CommandsPage Hello Set the specified RS485 address Read the RS485 address of the active boardRS485 Responses Examples Page Page Board selection by the supplied utilities Introduction Appendix E Fill ModeHardware Inputs Special ModeInput #1 Input #2 Input #3 Input #4 Output #1 Output #2 Output #3 Output #4 Hardware OutputsFilling By = Weight Filling By WeightFilling Parameters TimeAuto Tare Activate Auto Correction Averaging x last fillingsHi Limit Lo LimitStart from filling # … Valid Results LimitsValid Limits ± … % Stabilization Criterion Tare & Stop Filling By = Time Fast Speed ConfigStabilization Criterion Stop Filling Configurations Library LED Display Notations Scale of the displayed weight# 1 A= 40.99 Tr= 6.65 Cv= 0.00 Ft= 7527 ms St= 2554 ms Cc= Get current status small ‘s’ Response Example Error Codes Load Cell Input Appendix F SpecificationsCard does not respond after PC power-on Appendix G Trouble-shootingZero function Appendix H Zero & TareManual Zero Parameter Auto-TarefunctionWARRANTY/DISCLAIMER Temperature