Omega Speaker Systems LCIC-WIM-BEN manual Auto-Tarefunction, Parameter

Page 84

H.2 The Auto-Tarefunction

This function supplies a way to define the meaning of the setpoint

parameter:

*When the ‘AutoTare’ option is not activated, the setpoint

defines the requested final gross weight.

That is, if the setpoint is 100 kg and the starting gross weight is 90 kg, the filling amount will be 10 kg.

*When the ‘AutoTare’ option is activated, the setpoint defines the requested filling amount.

That is, if the setpoint is 100 kg, the filling amount will also be 100 kg, regardless of the starting gross weight.

However, the filling operation will take place only if the starting gross weight is within a user pre-defined range; otherwise, the filling operation will be rejected and an error will be indicated.

The activation of the ‘Auto-Tare’ option as well as its parameters are described in section E.4.1.2.

83

Image 84

Contents LCIC-WIM-BEN Servicing North America Table of Contents Programming your Application Appendices O & the LED DisplayTrouble-shooting Introduction General DescriptionTypical Applications Installing the board in the PC Page After a while, you’ll have this display Click ‘Finish’ Setup & Running Run the setups of the LCIC-WIM utilities in the foldersUtilities Run a utilityCalibration Utility GeneralThree stages are Show Data step Pseudo Calibration stepsFive calibration steps are Page Page Page Page Restore Calibrations LibrarySave Parameters Calibration Efficiency CE Settings Utility Menu BarTools / Analog Output Tools / Baud Rate for SCI port Tools / General Setpoints  The address setting takes effect only upon board reset CommunicationPort Baud RateGet results immediately Auto Zero ActivateMax Zero Min ZeroPage Filtering Filter1 Filter2 DecimatorFilling Definition Commands Programming your ApplicationGet a single reading RS485 Address selection, setting & reading Misc Summary of Weight & A/D Reading Commands Parameters Parameter Parameter Description Data Number TypeBecomes effective only after a system reset either Calibration Name 32 characters max LCIC-WIM ActiveX Start/Stop CommunicationVariables GetVariablerVariable NameVariables Table Category Variable Name Description Get SetVariables Table cont’d AnalogOutputM = Manual, 1 = Auto Internal updates there will be a Filters Parameter that needs no changeFast Mode FilteringLevel IntegerTransmission sends blocks of information Stage How to work with the Fast Mode in VB using the ActiveX Misc Interpreting the data in a blockAppendix a I/O & the LED Display General Notes about the I/ODigital Inputs Analog OutputPin Function ConnectionsConnecting External Devices to the Inputs LCIC-WIM I/O & Analog Out LED Display Appendix B Scaling the Load Cell Input Appendix C Load Cell Connections Appendix D USB, RS232 & RS485 Communication ParametersBaud Rate RS485 RS485 Commands Activate address x x=1, 2, 3, …, 62, 63Page Hello Read the RS485 address of the active board Set the specified RS485 addressRS485 Responses Examples Page Page Board selection by the supplied utilities Appendix E Fill Mode IntroductionSpecial Mode Hardware InputsInput #1 Input #2 Input #3 Input #4 Hardware Outputs Output #1 Output #2 Output #3 Output #4Filling By Weight Filling By = WeightFilling Parameters TimeAuto Correction Averaging x last fillings Auto Tare ActivateHi Limit Lo LimitValid Results Limits Start from filling # …Valid Limits ± … % Stabilization Criterion Tare & Stop Fast Speed Config Filling By = TimeStabilization Criterion Stop Filling Configurations Library Scale of the displayed weight LED Display Notations# 1 A= 40.99 Tr= 6.65 Cv= 0.00 Ft= 7527 ms St= 2554 ms Cc= Get current status small ‘s’ Response Example Error Codes Appendix F Specifications Load Cell InputAppendix G Trouble-shooting Card does not respond after PC power-onAppendix H Zero & Tare Zero functionManual Zero Auto-Tarefunction ParameterWARRANTY/DISCLAIMER Temperature