Omega Speaker Systems LCIC-WIM-BEN manual Fast Mode, FilteringLevel Integer

Page 45

4.3.4 Fast Mode

(The Fast Mode is not available with RS485.)

During the Fast Mode there is auto high speed transmission of weight readings to the communication. About the transmission rate, refer to the ‘Fast Mode’ square in the variables table above.

At the end, a ‘timer stamp’ is appended. Its value is the time elapsed from start of transmission until end of transmission, in ms.

The readings that are returned in this mode are always integers and they equal the actual weight multiplied by 1, 10, 100, 1000 or 10000, depending upon the resolution setting. So, although the readings are integers, due to that multiplication the original precision is maintained. The readings are not rounded to the resolution. For example, if the resolution is 0.05, then the readings transmitted by the board will be multiplied by 100, so that ‘123’ will represent ‘1.23’.

Start_Fast_Mode(Filtering_Level)

Starts the Fast Mode.

Note: During the Fast Mode the LED Display is not updated.

Filtering_Level (Integer):

1 = Supply readings after Filter1.

2 = Supply readings after Filter2.

Stop_Fast_Mode()

Stops the Fast Mode.

(A timer stamp is appended. Its value is the time elapsed from start of transmission until end of transmission, in ms.)

44

Image 45

Contents LCIC-WIM-BEN Servicing North America Table of Contents Programming your Application O & the LED Display AppendicesTrouble-shooting Introduction General DescriptionTypical Applications Installing the board in the PC Page After a while, you’ll have this display Click ‘Finish’ Run the setups of the LCIC-WIM utilities in the folders Setup & RunningUtilities Run a utilityGeneral Calibration UtilityThree stages are Show Data step Pseudo Calibration stepsFive calibration steps are Page Page Page Page Restore Calibrations LibrarySave Parameters Calibration Efficiency CE Menu Bar Settings UtilityTools / Analog Output Tools / Baud Rate for SCI port Tools / General Setpoints Communication  The address setting takes effect only upon board resetPort Baud RateGet results immediately Activate Auto ZeroMax Zero Min ZeroPage Filtering Filter1 Filter2 DecimatorFilling Definition Programming your Application CommandsGet a single reading RS485 Address selection, setting & reading Misc Summary of Weight & A/D Reading Commands Parameter Parameter Description Data Number Type ParametersBecomes effective only after a system reset either Calibration Name 32 characters max Start/Stop Communication LCIC-WIM ActiveXGetVariablerVariable Name VariablesCategory Variable Name Description Get Set Variables TableVariables Table cont’d AnalogOutputM = Manual, 1 = Auto Internal updates there will be a Parameter that needs no change FiltersFilteringLevel Integer Fast ModeTransmission sends blocks of information Stage How to work with the Fast Mode in VB using the ActiveX Interpreting the data in a block MiscGeneral Notes about the I/O Appendix a I/O & the LED DisplayDigital Inputs Analog OutputConnections Pin FunctionConnecting External Devices to the Inputs LCIC-WIM I/O & Analog Out LED Display Appendix B Scaling the Load Cell Input Appendix C Load Cell Connections Communication Parameters Appendix D USB, RS232 & RS485Baud Rate RS485 Activate address x x=1, 2, 3, …, 62, 63 RS485 CommandsPage Hello Set the specified RS485 address Read the RS485 address of the active boardRS485 Responses Examples Page Page Board selection by the supplied utilities Introduction Appendix E Fill ModeSpecial Mode Hardware InputsInput #1 Input #2 Input #3 Input #4 Output #1 Output #2 Output #3 Output #4 Hardware OutputsFilling By = Weight Filling By WeightFilling Parameters TimeAuto Tare Activate Auto Correction Averaging x last fillingsHi Limit Lo LimitValid Results Limits Start from filling # …Valid Limits ± … % Stabilization Criterion Tare & Stop Fast Speed Config Filling By = TimeStabilization Criterion Stop Filling Configurations Library LED Display Notations Scale of the displayed weight# 1 A= 40.99 Tr= 6.65 Cv= 0.00 Ft= 7527 ms St= 2554 ms Cc= Get current status small ‘s’ Response Example Error Codes Load Cell Input Appendix F SpecificationsCard does not respond after PC power-on Appendix G Trouble-shootingAppendix H Zero & Tare Zero functionManual Zero Parameter Auto-TarefunctionWARRANTY/DISCLAIMER Temperature