Liebert GXT2-6000RTL630 user manual Removable Power Distribution Box, Manual, Connections

Page 13

Major Components

Figure 3 Internal battery pack with connector

3.3Removable Power Distribution Box

The UPS incorporates a power distribution box that must be installed before the unit is placed into service. The power distribution box provides the benefits of plug and receptacle convenience with a manual bypass switch. For installation instructions, see 5.4 - Connect Input/Output Power.

Optional versions may be available to replace the standard box for custom installations.

Figure 4 Optional power distribution—PD-L630

Manual	Wired
Manual	connections
Bypass	to UPS
Switch

UPS	MAITANENCE BYPASS
AVAILABLE	MAITANENCE BYPASS
	AVAILABLE

UPS

ON	ON

OUTPUT
BREAKER		OUTPUT
20A	240V~/T
		BREAKER
OFF		20A	240V~/T
	OFF

		INPPUT
BREAKER 30A	OFF	ON
	OFF	ON

OUTPUT ONLY
	CB DOES NOT
CONNECT BYPASS		POWER TO
MANUAL
	BYPASS SWITCH.

REMOVE SCREWS	COVER COMMUNICATION
CONNECTOR PROTECTIVE COVER DO NOT	PRIOR TO INSTALLATION OF BOX ON UPS -LOOSEN THREE SCREWS 1 TURN - SLIDE COVER TO EXPOSE CONNECTOR -TIGHTEN SCREWS GENTLY UPON REMOVAL OF BOX FROM UPS -LOOSEN THREE SCREWS 1 TURN -SLIDE COVER TO REACH END SCREW AND	-TIGHTEN SCREWS GENTLY

9

Image 13

Contents Liebert GXT2-6000RTL630 Page Table of Contents Troubleshooting MaintenanceSpecifications Operating InstructionsElectromagnetic Compatibility Important Safety InstructionsPage Glossary of Symbols Introduction Battery Charger Rectifier/Power Factor Correction PFC CircuitInverter System DescriptionDC-to-DC Converter BatteryDynamic Bypass Lower Bezel Battery Access Door Upper Top Trim 2 pieces tower use only Status IndicatorsMain Frame and Electronics Major ComponentsBattery Disconnect External Battery Connector Internal Battery PacksFans UPS Output Circuit Breaker DB-9 Communication Port Relay Card SlotBypass To UPS Switch Removable Power Distribution BoxManual ConnectionsWHAT’S Included Configuration Disk DB-9 port coverInstallation and Configuration Install the Main CabinetTower UPS Installation Attach Bezels to TopInstalling the Adjustable Rack-Mount Kit-Sold Separately Rack-Mount UPS InstallationQuantity Return flanges Retaining Latches Front Innermembers membersScrews UPS or Install the Internal BatteriesCabinet Apply grease inside Push it into the rackConnect Input/Output Power Connect the Internal Batteries Using the External ConnectorBattery Door Captive Screws Remove these screws to release connectorFront of PD-L630 power distribution box Attach Power Distribution BoxLoosen these three Distribution Box Electrical Connections UPSExternal Battery Cabinet Installation Initial START-UP and Electrical Checks Configuration Program GXT2-6000RTL630 Configuration Program FeaturesWhat You Will Need Controls and Indicators ON/Alarm Silence/Manual Battery Test ButtonAll indicators illuminated for illustration only Standby/Manual Bypass ButtonBattery Level Indicators 5 Green Load Level Indicators 4 Green, 1 AmberFault Indicator LED Red Bypass Indicator LED AmberBattery Mode Operation Normal Mode OperationBypass Mode Operation Battery Recharge ModeCommunications Interface Port Pin 4 Remote Shutdown on BatteryCommunications DB-9 pin assignmentLiebert’s Ocwebcard DB9 RS232 port covered UPS Intelligent CommunicationsRepo switch connection diagram Remote Emergency Power OffMaintenance Internal BatteryBattery Door Captive Screws 3U Battery Access Door Internal Battery ReplacementBattery Connectors Retaining screw Retaining bracketDisconnect AC Power ConnectionsCaptive Box toReconnect Indicator meanings TroubleshootingLED status Diagnosis/Audible alarm UPS Troubleshooting guideAlarm conditions Troubleshooting guide cont’dBattery run times Auto-Learning Battery Run Times UPS specifications SpecificationsOutput distribution specifications Internal battery specificationsBattery Parameters External battery cabinet specificationsModel Number Page Iti Ne tTi n That