Liebert GXT2-6000RTL630 Load Level Indicators 4 Green, 1 Amber, Battery Level Indicators 5 Green

Page 26

Controls and Indicators

8.3Load Level Indicators (4 Green, 1 Amber)

The load level indicators display the approximate electrical load placed upon the UPS at all times.

8.4Battery Level Indicators (5 Green)

The battery level indicators display approximate battery capacity at all times.

The GXT2-6000RTL630 is equipped with automatic and remote battery test features. The automatic test occurs every 14 days (this option is user configurable) if utility power has not been interrupted. Should the battery fail this test, the red Fault indicator LED along with the A and C diagnostic LEDs will illuminate and an alarm will sound (refer to 12.0 - Troubleshooting). The remote test feature functions with MultiLink 3.x software and can remotely initiate the battery test.

8.5Fault Indicator LED (Red)

The Fault indicator LED is illuminated if the UPS has detected a problem. Also, one or more of the battery level indicators may be illuminated (refer to 12.0 - Troubleshooting).

8.6Bypass Indicator LED (Amber)

The Bypass indicator LED is illuminated when the UPS is operating from bypass power. An alarm will sound indicating the UPS detected a problem, or the manual bypass function has been activated.

8.7UPS ON Indicator LED (Green)

The UPS ON indicator LED is illuminated when the UPS inverter is operating and supplying power to the connected loads.

8.8Battery Indicator LED (Amber)

The Battery indicator LED is illuminated when the UPS is operating on battery.

8.9AC Input Indicator LED (Green)

The AC Input indicator LED is illuminated when utility power is available and within the input spec- ifications.

22

Image 26

Contents Liebert GXT2-6000RTL630 Page Table of Contents Specifications MaintenanceTroubleshooting Operating InstructionsImportant Safety Instructions Electromagnetic CompatibilityPage Glossary of Symbols Introduction Inverter Rectifier/Power Factor Correction PFC CircuitBattery Charger System DescriptionDynamic Bypass BatteryDC-to-DC Converter Main Frame and Electronics Top Trim 2 pieces tower use only Status IndicatorsLower Bezel Battery Access Door Upper Major ComponentsFans UPS Output Circuit Breaker DB-9 Communication Port Internal Battery PacksBattery Disconnect External Battery Connector Relay Card SlotManual Removable Power Distribution BoxBypass To UPS Switch ConnectionsConfiguration Disk DB-9 port cover WHAT’S IncludedTower UPS Installation Install the Main CabinetInstallation and Configuration Attach Bezels to TopQuantity Rack-Mount UPS InstallationInstalling the Adjustable Rack-Mount Kit-Sold Separately Return flanges Retaining Latches Front Innermembers membersScrews Cabinet Install the Internal BatteriesUPS or Apply grease inside Push it into the rackBattery Door Captive Screws Connect the Internal Batteries Using the External ConnectorConnect Input/Output Power Remove these screws to release connectorLoosen these three Attach Power Distribution BoxFront of PD-L630 power distribution box UPS Distribution Box Electrical ConnectionsExternal Battery Cabinet Installation Initial START-UP and Electrical Checks What You Will Need GXT2-6000RTL630 Configuration Program FeaturesConfiguration Program All indicators illuminated for illustration only ON/Alarm Silence/Manual Battery Test ButtonControls and Indicators Standby/Manual Bypass ButtonFault Indicator LED Red Load Level Indicators 4 Green, 1 AmberBattery Level Indicators 5 Green Bypass Indicator LED AmberBypass Mode Operation Normal Mode OperationBattery Mode Operation Battery Recharge ModeCommunications Pin 4 Remote Shutdown on BatteryCommunications Interface Port DB-9 pin assignmentUPS Intelligent Communications Liebert’s Ocwebcard DB9 RS232 port coveredRemote Emergency Power Off Repo switch connection diagramInternal Battery MaintenanceBattery Connectors Internal Battery ReplacementBattery Door Captive Screws 3U Battery Access Door Retaining screw Retaining bracketCaptive AC Power ConnectionsDisconnect Box toReconnect LED status Diagnosis/Audible alarm TroubleshootingIndicator meanings Troubleshooting guide UPSTroubleshooting guide cont’d Alarm conditionsBattery run times Auto-Learning Battery Run Times Specifications UPS specificationsInternal battery specifications Output distribution specificationsModel Number External battery cabinet specificationsBattery Parameters Page Ti n Ne tIti That