Liebert GXT2-6000RTL630 Internal battery specifications, Output distribution specifications

Page 41

Specifications

Table 7	Internal battery specifications

	Model Number	GXT2-240BATKIT

Dimensions, W x D x H, in. (mm)

	Shipping	21.2 x 12.2 x 16.2 (539 x 311 x 412)

Weight, lb (kg)

	Unit	44.5 (20.2) each, (2 required)

	Shipping	93.9 (42.6), (2 batteries in a single carton

	Type	Valve-regulated, non-spillable, lead acid

	Quantity x V	20 x 12V

	Battery Mfr. / Part #	Yuasa / REW 28-12FT

Electrical Characteristics

	Back-up Time	See Table 5 - Battery run times

	Recharge Time	3 hrs. to 90% capacity after full discharge into 100% load

Table 8	Output distribution specifications
	Model Number	PD-L630

Dimensions, W x D x H, in. (mm)

	Unit	5.3 x 6.9 x 3.5 (134 x 175 x 88)

	Shipping	8.9 x 10.4 x 12.4 (225 x 265 x 315)

Weight, lb (kg)

	Unit	30 (13.5)

	Shipping	33 (15)

Electrical Specifications

	Amp Rating	24 Amps

	Input Power Connections	L6-30P on 10-foot (3m) cord

Output Power Connection: L1-L2-G		(2) L6-30R on a 12" (300mm) cord
Output Power Connection: L1-L2-G		(2) L6-20R on a 12" (300mm) cord
		(2) L6-20R on a 12" (300mm) cord

Image 41

Contents Liebert GXT2-6000RTL630 Page Table of Contents Troubleshooting MaintenanceSpecifications Operating InstructionsElectromagnetic Compatibility Important Safety InstructionsPage Glossary of Symbols Introduction Battery Charger Rectifier/Power Factor Correction PFC CircuitInverter System DescriptionDynamic Bypass BatteryDC-to-DC Converter Lower Bezel Battery Access Door Upper Top Trim 2 pieces tower use only Status IndicatorsMain Frame and Electronics Major ComponentsBattery Disconnect External Battery Connector Internal Battery PacksFans UPS Output Circuit Breaker DB-9 Communication Port Relay Card SlotBypass To UPS Switch Removable Power Distribution BoxManual ConnectionsWHAT’S Included Configuration Disk DB-9 port coverInstallation and Configuration Install the Main CabinetTower UPS Installation Attach Bezels to TopInstalling the Adjustable Rack-Mount Kit-Sold Separately Rack-Mount UPS InstallationQuantity Return flanges Retaining Latches Front Innermembers membersScrews UPS or Install the Internal BatteriesCabinet Apply grease inside Push it into the rackConnect Input/Output Power Connect the Internal Batteries Using the External ConnectorBattery Door Captive Screws Remove these screws to release connectorLoosen these three Attach Power Distribution BoxFront of PD-L630 power distribution box Distribution Box Electrical Connections UPSExternal Battery Cabinet Installation Initial START-UP and Electrical Checks What You Will Need GXT2-6000RTL630 Configuration Program FeaturesConfiguration Program Controls and Indicators ON/Alarm Silence/Manual Battery Test ButtonAll indicators illuminated for illustration only Standby/Manual Bypass ButtonBattery Level Indicators 5 Green Load Level Indicators 4 Green, 1 AmberFault Indicator LED Red Bypass Indicator LED AmberBattery Mode Operation Normal Mode OperationBypass Mode Operation Battery Recharge ModeCommunications Interface Port Pin 4 Remote Shutdown on BatteryCommunications DB-9 pin assignmentLiebert’s Ocwebcard DB9 RS232 port covered UPS Intelligent CommunicationsRepo switch connection diagram Remote Emergency Power OffMaintenance Internal BatteryBattery Door Captive Screws 3U Battery Access Door Internal Battery ReplacementBattery Connectors Retaining screw Retaining bracketDisconnect AC Power ConnectionsCaptive Box toReconnect LED status Diagnosis/Audible alarm TroubleshootingIndicator meanings UPS Troubleshooting guideAlarm conditions Troubleshooting guide cont’dBattery run times Auto-Learning Battery Run Times UPS specifications SpecificationsOutput distribution specifications Internal battery specificationsModel Number External battery cabinet specificationsBattery Parameters Page Iti Ne tTi n That

Internal battery specifications

GXT2-240BATKIT

Output distribution specifications

Electrical Specifications