Lantronix UDS1100 manual Product Information Label, Sample Hardware Address

Page 12

2: Introduction

Product Information Label

The product information label on the underside of the unit contains the following information about your specific unit:

Bar code

Serial number

Product ID (name)

Product description

Hardware address (also referred to as the Ethernet or MAC address)

The first three bytes of the hardware address are fixed and read 00-20-4A, identifying the unit as a Lantronix product. The fourth, fifth, and sixth bytes are unique numbers assigned to each unit.

Figure 2-3. Sample Hardware Address

00-20-4A-14-01-18 or 00:20:4A:14:01:18

UDS1100 User Guide

12

Image 12

Contents UDS1100 User Guide Copyright & Trademark ContactsRevisions Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesUsing This Guide Purpose and AudienceChapter Summary Using This Guide Additional DocumentationIntroduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitRequired Information Hardware AddressIP Address IP Address Subnet Mask GatewayAssigning the IP Address DeviceInstaller Installing DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click NextAccessing the UDS1100 Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationServer Configuration Ethernet ConfigurationTo specify how data will be transmitted To configure the UDS1100’s device server settings Server ConfigurationAdvanced Host List Configuration To configure the host listRetry Settings Channel 1 Configuration Serial SettingsTo configure the channel’s serial settings Host InformationPort Settings ChannelPack Control Connection Settings TCP To configure a channel’s TCP settingsFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolConnect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connectionExiting Setup Mode To exit setup modeSerial Port Connection Setup Mode Server Configuration Server Configuration OptionIP Address Set Gateway IP AddressChange Telnet Configuration Password Netmask Number of Bits for Host PartDhcp Name Network Class Host Bits NetmaskSetup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Interface Mode Mode OptionCommon I/F Mode Setting Binary FlowConnect Mode Port NumberFlow Control Option Hex Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example Modem Mode To enable the hostlistDatagram Type MessageMeaning No CarrierModem Mode Function Command ATDSend the Escape Sequence +++ in Modem Mode Auto Increment Source PortRemote IP Address Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionDisConnTime Inactivity Timeout Send CharactersPacking Interval Trailing CharactersChannel Port Password Telnet Terminal TypeSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds ARP Cache timeout in seconds Disable Monitor Mode at bootupEnable alternate MAC Http Port NumberSecurity Settings Option Disable SnmpDisable Telnet Setup Snmp Community NameDisable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web SetupDefault Settings Option Channel 1 Configuration DefaultsExpert Settings Defaults Security Settings DefaultsSetup Mode Advanced Settings Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaSerial Connector Pinouts Connections and PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConverting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide