Lantronix Explore UDS1100 Manual for Default Password and Channel Configuration Options

Page 50

7: Setup Mode: Channel Configuration

Table 7-7. Disconnect Mode Options

Disconnect Mode Option

7

6

5

4

3

2

1

0

Disconnect with DTR drop (6)

1

 

 

 

 

Ignore DTR

0

 

 

 

 

Telnet mode and terminal type setup (1)

 

1

 

 

 

Channel (port) password (2)

 

 

 

1

 

Hard disconnect (3)

 

 

 

 

0

Disable hard disconnect

 

 

 

 

1

State LED off with connection (4)

 

 

 

 

 

Disconnect with EOT (^D) (5)

 

 

1

 

 

 

 

 

 

 

 

1

(1)The UDS sends the "Terminal Type" upon an outgoing connection.

(2)A password is required for a connection to the serial port from the network.

(3)The TCP connection closes even if the remote site does not acknowledge the disconnection.

(4)When there is a network connection to or from the serial port, the state LED turns off instead of blinking.

(5)When Ctrl+D or Hex 04 is detected, the connection is dropped. Both Telnet Mode and Disconnect with EOT must be enabled for Disconnect with EOT to function properly. Ctrl+D is only detected going from the serial port to the network.

(6)When DTR transitions from a high state to a low state, the network connection to or from the serial port drops.

Flush Mode (Buffer Flushing)

Using this parameter, you can control line handling and network buffers with connection startup and disconnect. The default setting is 00.

FlushMode (00) ? _

You can also select between two different packing algorithms.

Note: All bit positions in the table that are blank represent “don’t care” bits for that particular option, which can be set to either a 0 or 1 value.

UDS1100 User Guide

50

Image 50
Contents UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesChapter Summary Using This GuidePurpose and Audience Using This Guide Additional DocumentationApplication Examples IntroductionApplications Introduction Protocol Support Additional FeaturesConfiguration Methods Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationTo specify how data will be transmitted Server ConfigurationEthernet Configuration Advanced To configure the UDS1100’s device server settingsServer Configuration Retry Settings Host List ConfigurationTo configure the host list To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host InformationPack Control Port SettingsChannel Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolCommon Options Connect Mode Active ConnectionEndpoint Configuration To configure a channel’s UDP settings Connection Settings UDPDisconnect Mode Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connectionSerial Port Connection Exiting Setup ModeTo exit setup mode IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Baudrate Setup Mode Channel ConfigurationChannel 1 Option Common I/F Mode Setting Binary Interface ModeMode Option FlowFlow Control Option Hex Connect ModePort Number Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example Datagram Type Modem ModeTo enable the hostlist MessageMeaning No CarrierModem Mode Function Command ATDRemote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionPacking Interval DisConnTime Inactivity TimeoutSend Characters Trailing CharactersChannel Port Password Telnet Terminal TypeTCP Keepalive time in seconds Setup Mode Advanced SettingsExpert Settings Option Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaSerial Port Serial Connector PinoutsConnections and Pinouts DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressDecimal Binary Hex Converting Binary to HexadecimalConversion Table Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide