Lantronix UDS1100 ARP Cache timeout in seconds, Disable Monitor Mode at bootup, Http Port Number

Page 55

8: Setup Mode: Advanced Settings

ARP Cache timeout in seconds

Whenever the unit communicates with another device on the network, it adds an entry into its ARP table. The ARP Cache timeout option allows you to define how many seconds (1-600) the unit will wait before timing out this table. The default setting is 600.

ARP Cache timeout in s (1s – 65s; 0s=disable): (600)? _

Disable Monitor Mode at bootup

This option allows you to disable all entries into Monitor Mode during startup, except for the ‘xxx’ sequence. This prevents entry using yyy, zzz, xx1, and yy1 key sequences (only during the bootup sequence). The default for Monitor Mode at bootup is N (No). (See 10: Monitor Mode.)

Monitor Mode @ bootup : enabled

HTTP Port Number

This option allows the configuration of the web server port number. The valid range is 1-65535. The default HTTP port number is 80.

HTTP Port Number : (80) ? _

MTU Size

The Maximum Transmission Unit (MTU) is the largest physical packet size a network can transmit for TCP and UDP. Enter between 512 and 1400 bytes. The default setting is 1400 bytes.

MTU Size: (1400) ? _

Enable alternate MAC

If necessary, enable the alternate MAC address (if specified in the OEM setup record). The default setting is N (No).

Enable alternate MAC (N) ? _

Ethernet connection type

The UDS1100 allows for the Ethernet speed and duplex to be manually configured. Enter 0 for auto-negotiation (default). To select the speed and duplex, enter one of the following: 2 (10Mbit/half duplex), 3 (10Mbit/full duplex), 4 (100Mbit/half duplex), or 5 (100Mbit/full duplex).

Ethernet connection type: (0) ? _

UDS1100 User Guide

55

Image 55

Contents UDS1100 User Guide Date Rev Comments 900-417 Copyright & TrademarkContacts RevisionsContents Setup Mode Server Configuration Troubleshooting and Contact Information Tables ContentsPurpose and Audience Using This GuideChapter Summary Additional Documentation Using This GuideApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Sample Hardware Address Product Information LabelGetting Started Package ContentsTo install the unit Installing the UDSIP Address Subnet Mask Gateway Required InformationHardware Address IP AddressSelect Assign a specific IP address and click Next Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressAdding the Unit to the Manage List Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration To view the units current settingsIP Address on Next Step Assigning the IP Address Serial Port LoginGetting Started Accessing UDS1100 Using DeviceInstaller Configuration Using Web-ManagerLantronix Web-Manager Network ConfigurationStatic IP Address Configuration Automatic IP Address ConfigurationEthernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings Host Information Channel 1 ConfigurationSerial Settings To configure the channel’s serial settingsChannel Port SettingsPack Control Flush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings Flush Input Buffer Serial to NetworkConnect Protocol Connect Mode Passive ConnectionEndpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings UDP Connection Settings Datagram ModeApply Factory Defaults Apply SettingsTo establish a Telnet connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode Telnet ConnectionTo exit setup mode Exiting Setup ModeSerial Port Connection Set Gateway IP Address Setup Mode Server ConfigurationServer Configuration Option IP AddressNetwork Class Host Bits Netmask Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Dhcp NameSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Flow Interface ModeMode Option Common I/F Mode Setting BinaryPort Numbers Reserved for Connect ModePort Number Flow Control Option HexIncoming Connection Connect Mode OptionActive Startup ResponseManual Connection Address Example To enable the hostlist Modem ModeDatagram Type No Carrier MessageMeaningATD Modem Mode Function CommandRemote Port Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote IP AddressDisconnect Mode Option Flush Mode Buffer FlushingOption Pack Control Trailing Characters DisConnTime Inactivity Timeout Send Characters Packing IntervalTelnet Terminal Type Channel Port PasswordExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Http Port Number ARP Cache timeout in secondsDisable Monitor Mode at bootup Enable alternate MACSnmp Community Name Security Settings OptionDisable Snmp Disable Telnet SetupDisable Web Setup Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web ServerSecurity Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Expert Settings DefaultsSetup Mode Advanced Settings ROM File Firmware UpgradesUsing Tftp Graphical User Interface Obtaining Firmware Reloading FirmwareTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Monitor Mode Commands Monitor ModeEntering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network PortResponse Meaning Command Command Name FunctionLEDs Troubleshooting and Contact InformationProblem/Message Reason Solution Problems and Error MessagesLock on Technical Support Europe, Middle East, and Africa Technical SupportConnections and Pinouts Serial Connector PinoutsSerial Port Modem Cable DB25 Female Interface RS422 4 wire modeNull Modem Cable Lantronix Part No Network PortPower Plug Ethernet Connector PinoutsCategory Description Technical SpecificationsTechnical Specifications AutoIP Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide