Lantronix UDS1100 manual IP Address on

Page 18

		3: Getting Started

	Type	Non-configurable field. Displays the device type as UDS1100.

	ID	Non-configurable field. Displays the UDS1100’s ID embedded
		within the box.

	Hardware Address	Non-configurable field. Displays the UDS1100’s hardware (or
		MAC) address.

	Firmware Version	Non-configurable field. Displays the firmware currently
		installed on the UDS1100.

	Extended Firmware	Non-configurable field. Displays the full version nomenclature
	Version	of the firmware.

	Online Status	Non-configurable field. Displays the UDS1100’s status as
		online, offline, unreachable (the UDS1100 is on a different
		subnet), or busy (the UDS1100 is currently performing a task).

	Telnet Enabled	Non-configurable field. Permits Telnet sessions.

	Telnet Port	Non-configurable field. Displays the UDS1100’s port for telnet
		sessions.

	Web Enabled	Non-configurable field. Permits configuration through Web-
		Manager.

	Web Port	Non-configurable field. Displays the UDS1100’s port for Web-
		Manager configuration.

	Maximum Baud Rate	Non-configurable field. Displays the UDS1100’s maximum
	Supported	baud rate.
		Note: The UDS1100 may not currently be running at this rate.

	Firmware Upgradeable	Non-configurable field. Displays True, indicating the
		UDS1100’s firmware is upgradeable as newer version
		become available.

	IP Address	Non-configurable field. Displays the UDS1100’s current IP
		address. To change the IP address, see Assigning an IP
		Address on page 16.

	Number of COB partitions	Non-configurable field. Displays the number of COB partitions
	supported	supported.

	Supports Dynamic IP	Non-configurable field. Indicates whether the current IP
		address on the UDS1100 was set manually or assigned by
		DHCP.

	Subnet Mask	Non-configurable field. Displays the UDS1100’s current
		subnet mask. To change the subnet mask, see Assigning an
		IP Address on page 16.

	Gateway	Non-configurable field. Displays the UDS1100’s current
		gateway. To change the gateway, see Assigning an IP
		Address on page 16.

	Number of Ports	Non-configurable field. Displays the number of ports on the
		UDS1100.

	TCP Keepalive	Non-configurable field. Displays the UDS1100’s TCP
		keepalive value. The value is in the range 1-65s, and the
		default setting is 45.

UDS1100 User Guide

18

Image 18

Contents UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesUsing This Guide Purpose and AudienceChapter Summary Using This Guide Additional DocumentationIntroduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationServer Configuration Ethernet ConfigurationTo specify how data will be transmitted To configure the UDS1100’s device server settings Server ConfigurationAdvanced Host List Configuration To configure the host listRetry Settings To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host InformationPort Settings ChannelPack Control Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolConnect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connectionExiting Setup Mode To exit setup modeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Common I/F Mode Setting Binary Interface ModeMode Option FlowFlow Control Option Hex Connect ModePort Number Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example Modem Mode To enable the hostlistDatagram Type MessageMeaning No CarrierModem Mode Function Command ATDRemote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionPacking Interval DisConnTime Inactivity TimeoutSend Characters Trailing CharactersChannel Port Password Telnet Terminal TypeSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaSerial Connector Pinouts Connections and PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConverting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide