Lantronix UDS1100 manual Setup Mode Channel Configuration, Channel 1 Option, Baudrate

Page 40

7: Setup Mode: Channel Configuration

This chapter explains how to configure the serial port.

Notes:

Current values display in parenthesis.

You must enter some values in hexadecimal notation. (See B: Binary to Hexadecimal Conversions.)

Channel 1 (Option 1)

Select Channel 1 (option 1) from the Change Setup menu to define how the serial port responds to network and serial communications. The following sections describe the configurable parameters within the Channel configuration menu.

Figure 7-1. Serial Port Settings

Baudrate

The unit and attached serial device, such as a modem, must agree on a speed or baud rate to use for the serial connection. Valid baud rates are 300, 600, 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 115200, and 230400 baud.

Baudrate (9600) ? _

UDS1100 User Guide

40

Image 40

Contents UDS1100 User Guide Copyright & Trademark ContactsRevisions Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesPurpose and Audience Using This GuideChapter Summary Using This Guide Additional DocumentationApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitRequired Information Hardware AddressIP Address IP Address Subnet Mask GatewayAssigning the IP Address DeviceInstaller Installing DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click NextAccessing the UDS1100 Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationEthernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings Channel 1 Configuration Serial SettingsTo configure the channel’s serial settings Host InformationChannel Port SettingsPack Control Connection Settings TCP To configure a channel’s TCP settingsFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolEndpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connectionTo exit setup mode Exiting Setup ModeSerial Port Connection Setup Mode Server Configuration Server Configuration OptionIP Address Set Gateway IP AddressChange Telnet Configuration Password Netmask Number of Bits for Host PartDhcp Name Network Class Host Bits NetmaskSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Interface Mode Mode OptionCommon I/F Mode Setting Binary FlowConnect Mode Port NumberFlow Control Option Hex Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example To enable the hostlist Modem ModeDatagram Type MessageMeaning No CarrierModem Mode Function Command ATDSend the Escape Sequence +++ in Modem Mode Auto Increment Source PortRemote IP Address Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionDisConnTime Inactivity Timeout Send CharactersPacking Interval Trailing CharactersChannel Port Password Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds ARP Cache timeout in seconds Disable Monitor Mode at bootupEnable alternate MAC Http Port NumberSecurity Settings Option Disable SnmpDisable Telnet Setup Snmp Community NameDisable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web SetupDefault Settings Option Channel 1 Configuration DefaultsExpert Settings Defaults Security Settings DefaultsSetup Mode Advanced Settings Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaConnections and Pinouts Serial Connector PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide