Lantronix UDS1100 manual Setup Mode Advanced Settings, Expert Settings Option

Page 54

8: Setup Mode: Advanced Settings

Expert Settings (Option 5)

Note: You can change these settings using Telnet or serial connections only, not on the Web-Manager.

Caution: Changing the expert settings can drastically affect the performance and access to the product. These settings should only be changed by an experienced network administrator.

Figure 8-1. Expert Settings

The default settings are listed below:

TCP Keepalive time in s	45
(1s – 65s; 0s=disable)

ARP Cache timeout in s	600
(1s – 600s)

Disable Monitor Mode @	Enabled
bootup

HTTP Port Number	80
(1-65535)
MTU Size (512 – 1400)	0 (resulting in an operational value of 1400)

Enable alternate MAC	Disabled (OEM use only)

Ethernet connection type	0 (resulting in auto-negotiation)

TCP Keepalive time in seconds

This option allows you to change how many seconds the unit waits during a silent connection before attempting to see if the currently connected network device is still on the network. If the unit gets no response, it drops that connection. The default setting is 45.

TCP Keepalive time in s (1s – 65s; 0s=disable): (45)? _

UDS1100 User Guide

54

Image 54

Contents UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesUsing This Guide Purpose and AudienceChapter Summary Using This Guide Additional DocumentationIntroduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationServer Configuration Ethernet ConfigurationTo specify how data will be transmitted To configure the UDS1100’s device server settings Server ConfigurationAdvanced Host List Configuration To configure the host listRetry Settings To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host InformationPort Settings ChannelPack Control Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolConnect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connectionExiting Setup Mode To exit setup modeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Common I/F Mode Setting Binary Interface ModeMode Option FlowFlow Control Option Hex Connect ModePort Number Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example Modem Mode To enable the hostlistDatagram Type MessageMeaning No CarrierModem Mode Function Command ATDRemote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionPacking Interval DisConnTime Inactivity TimeoutSend Characters Trailing CharactersChannel Port Password Telnet Terminal TypeSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaSerial Connector Pinouts Connections and PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConverting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide