Lantronix Comprehensive Guide to UDS1100 Configuration and Default IP Settings

Page 58

8: Setup Mode: Advanced Settings

Default Settings (Option 7)

Select 7 to reset the unit’s Channel 1 configuration and expert settings to the default settings. The server configuration settings for IP address, gateway IP address, and netmask remain unchanged. The configurable pins’ settings also remain unchanged. The specific settings that this option changes are listed below:

Channel 1 Configuration Defaults

Baudrate

9600

 

 

I/F Mode

4C (1 stop bit, no parity, 8 bit, RS-232C)

 

 

Own TCP port number

10001

 

 

Connect Mode

C0 (always accept incoming connection; no active

 

connection startup)

 

 

Hostlist retry counter

3

 

 

Hostlist retry timeout

250 (msec)

 

 

Start character for serial channel 1

0x0D (CR)

 

 

All other parameters

0

 

 

Expert Settings Defaults

TCP Keepalive time in s

45

 

 

ARP Cache timeout in s

600

 

 

Disable Monitor Mode @ bootup

No

 

 

HTTP Port Number

80

(1-65535)

 

 

 

MTU Size (512 – 1400)

1400

 

 

Enable alternate MAC

No ( for OEM use only)

 

 

Ethernet Connection Type

0 (auto-negotiate)

 

 

Security Settings Defaults

Disable SNMP

No

 

 

SNMP community name

public

 

 

Disable Telnet setup

No

 

 

Disable TFTP Firmware Update

No

 

 

Disable Port 77FEh

No

 

 

Disable Web Server

No

 

 

UDS1100 User Guide

58

Image 58
Contents UDS1100 User Guide Revisions Copyright & TrademarkContacts Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesPurpose and Audience Using This GuideChapter Summary Using This Guide Additional DocumentationApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitIP Address Required InformationHardware Address IP Address Subnet Mask GatewayAssigning an IP Address Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Select Assign a specific IP address and click NextTo view the units current settings Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationEthernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings To configure the channel’s serial settings Channel 1 ConfigurationSerial Settings Host InformationChannel Port SettingsPack Control Flush Input Buffer Serial to Network Connection Settings TCPTo configure a channel’s TCP settings Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolEndpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsTelnet Connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode To establish a Telnet connectionTo exit setup mode Exiting Setup ModeSerial Port Connection IP Address Setup Mode Server ConfigurationServer Configuration Option Set Gateway IP AddressDhcp Name Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Network Class Host Bits NetmaskSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Common I/F Mode Setting Binary Interface ModeMode Option FlowFlow Control Option Hex Connect ModePort Number Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example To enable the hostlist Modem ModeDatagram Type MessageMeaning No CarrierModem Mode Function Command ATDRemote IP Address Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionPacking Interval DisConnTime Inactivity TimeoutSend Characters Trailing CharactersChannel Port Password Telnet Terminal TypeExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Enable alternate MAC ARP Cache timeout in secondsDisable Monitor Mode at bootup Http Port NumberDisable Telnet Setup Security Settings OptionDisable Snmp Snmp Community NameDisable Web Server Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web SetupExpert Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Security Settings DefaultsSetup Mode Advanced Settings Obtaining Firmware Reloading Firmware Firmware UpgradesUsing Tftp Graphical User Interface ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Entering Monitor Mode Using the Network Port Monitor ModeEntering Monitor Mode Using the Serial Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaConnections and Pinouts Serial Connector PinoutsSerial Port DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide