Lantronix UDS1100 manual Technical Specifications, Category Description

Page 73

13: Technical Specifications

 

 

Table 13-1. UDS1100 Technical Specifications

Category

Description

CPU

Lantronix DSTNI-EX 48 MHz clock

 

 

Internal CPU Memory

256 KB zero wait state SRAM

 

 

Flash

2 MB Flash

 

 

EEPROM

2 KB EEPROM

 

 

Serial Interface

1 DB25F DCE serial port

 

 

Software-selectable baud rate from 300 to 230 KBaud

 

 

Software-selectable RS232, RS422 or RS485 (2 and 4 wire support)

 

 

Serial Line Formats

Characters: 7 or 8 data bits

 

 

Stop bits: 1 or 2

 

 

Parity: odd, even, none

 

 

Modem Control

DTR, DSR

 

 

Flow Control

Hardware: CTS/RTS

 

 

Software: XON/XOFF

 

 

Power Input

9-30 VDC or 9-24 VAC on barrel connector (1.5 Watts maximum consumption)

 

 

9-30 VDC on DB25F serial interface

 

 

Network Interface

1 RJ45 10Base-T/100Base-TX Ethernet port

 

 

Software selectable Ethernet speed 10/100/Auto

 

 

Software selectable Half/Full/Auto duplex

 

 

Dimensions

Height: 2.3 cm (0.9 in)

 

 

Width: 6.4 cm (2.5 in)

 

 

Depth: 9.0 cm (3.5 in)

 

 

Weight

0.20 kg (0.45 lb)

 

 

Temperature

Operating range: 5° to +50° C (41° to 122° F)

 

 

Storage -40° to 66° C (-40 to 151° F)

 

 

Relative Humidity

Operating 10% to 90% non-condensing, 40% to 60% recommended

 

 

Storage 10% to 90% non-condensing

 

 

Case

Metal enclosure with integrated wall mounts

 

 

Optional 35 mm Din Rail mount available

 

 

Protocols Supported

ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, and HTTP

 

 

Installable Industrial

ModBus TCP, ModBus ASCII/RTU, DF1 Multi-Master (IAP version only)

Protocols

 

 

 

Management

Internal web server

 

 

SNMP (read only)

 

 

Serial login

 

 

Telnet login

 

 

 

 

 

UDS1100 User Guide

73

Image 73
Contents UDS1100 User Guide Contacts Copyright & TrademarkRevisions Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Tables ContentsPurpose and Audience Using This GuideChapter Summary Additional Documentation Using This GuideApplications IntroductionApplication Examples Introduction Configuration Methods Additional FeaturesProtocol Support Sample Hardware Address Product Information LabelGetting Started Package ContentsTo install the unit Installing the UDSHardware Address Required InformationIP Address IP Address Subnet Mask GatewayInstalling DeviceInstaller Assigning the IP Address DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click NextViewing the Current Configuration Accessing the UDS1100 Using DeviceInstallerTo view the units current settings Adding the Unit to the Manage ListIP Address on Next Step Assigning the IP Address Serial Port LoginGetting Started Accessing UDS1100 Using DeviceInstaller Configuration Using Web-ManagerLantronix Web-Manager Network ConfigurationStatic IP Address Configuration Automatic IP Address ConfigurationEthernet Configuration Server ConfigurationTo specify how data will be transmitted Server Configuration To configure the UDS1100’s device server settingsAdvanced To configure the host list Host List ConfigurationRetry Settings Serial Settings Channel 1 ConfigurationTo configure the channel’s serial settings Host InformationChannel Port SettingsPack Control To configure a channel’s TCP settings Connection Settings TCPFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Protocol Connect Mode Passive ConnectionEndpoint Configuration Connect Mode Active ConnectionCommon Options Disconnect Mode Connection Settings UDPTo configure a channel’s UDP settings UDP Connection Settings Datagram ModeApply Factory Defaults Apply SettingsAccessing Setup Mode Configuration via Telnet or Serial Port Setup ModeTelnet Connection To establish a Telnet connectionTo exit setup mode Exiting Setup ModeSerial Port Connection Server Configuration Option Setup Mode Server ConfigurationIP Address Set Gateway IP AddressNetmask Number of Bits for Host Part Change Telnet Configuration PasswordDhcp Name Network Class Host Bits NetmaskSetup Mode Server Configuration Channel 1 Option Setup Mode Channel ConfigurationBaudrate Mode Option Interface ModeCommon I/F Mode Setting Binary FlowPort Number Connect ModeFlow Control Option Hex Port Numbers Reserved forIncoming Connection Connect Mode OptionActive Startup ResponseManual Connection Address Example To enable the hostlist Modem ModeDatagram Type No Carrier MessageMeaningATD Modem Mode Function CommandAuto Increment Source Port Send the Escape Sequence +++ in Modem ModeRemote IP Address Remote PortDisconnect Mode Option Flush Mode Buffer FlushingOption Pack ControlSend Characters DisConnTime Inactivity TimeoutPacking Interval Trailing CharactersTelnet Terminal Type Channel Port PasswordExpert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds Disable Monitor Mode at bootup ARP Cache timeout in secondsEnable alternate MAC Http Port NumberDisable Snmp Security Settings OptionDisable Telnet Setup Snmp Community NameDisable Port 77FE Hex Disable Tftp Firmware UpdateDisable Web Server Disable Web SetupChannel 1 Configuration Defaults Default Settings OptionExpert Settings Defaults Security Settings DefaultsSetup Mode Advanced Settings Using Tftp Graphical User Interface Firmware UpgradesObtaining Firmware Reloading Firmware ROM FileTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Entering Monitor Mode Using the Serial Port Monitor ModeEntering Monitor Mode Using the Network Port Monitor Mode CommandsResponse Meaning Command Command Name FunctionLEDs Troubleshooting and Contact InformationProblem/Message Reason Solution Problems and Error MessagesLock on Technical Support Europe, Middle East, and Africa Technical SupportConnections and Pinouts Serial Connector PinoutsSerial Port Modem Cable DB25 Female Interface RS422 4 wire modeNull Modem Cable Lantronix Part No Network PortPower Plug Ethernet Connector PinoutsCategory Description Technical SpecificationsTechnical Specifications AutoIP Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetConversion Table Converting Binary to HexadecimalDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide