Lantronix UDS1100 manual Pack Control, Option

Page 51

7: Setup Mode: Channel Configuration

Table 7-8. Flush Mode Options

Function	7	6	5	4	3	2	1	0
Input Buffer (Serial to Network)

Clear with a connection initiated from the device to the network				1

Clear with a connection initiated from the network to the device			1

Clear when the network connection to or from the device is disconnected		1

Output Buffer (Network to Serial)

Clear with a connection initiated from the device to the network								1

Clear with a connection initiated from the network to the device							1

Clear when the network connection to or from the device is disconnected						1

Alternate Packing Algorithm (Pack Control)

Enable	1

Pack Control

The packing algorithms define how and when packets are sent to the network. The standard algorithm is optimized for applications in which the unit is used in a local environment, allowing for very small delays for single characters, while keeping the packet count low. The alternate packing algorithm minimizes the packet count on the network and is especially useful in applications in a routed Wide Area Network (WAN). Adjusting parameters in this mode can economize the network data stream.

Pack control settings are enabled in Flush Mode. Set this value to 00 if you do not need specific functions.

Note: All bit positions in the table that are blank represent “don’t care” bits for that particular option, which can be set to either a 0 or 1 value.

	Table 7-9. Pack Control Options
	Option	7	6	5	4	3	2	1	0
	Packing Interval

	Interval: 12 msec							0	0

	Interval: 52 msec							0	1

	Interval: 250 msec							1	0

	Interval: 5 sec							1	1

	Trailing Characters

	None					0	0

	One					0	1

	Two					1	0

UDS1100 User Guide

51

Image 51

Contents UDS1100 User Guide Date Rev Comments 900-417 Copyright & TrademarkContacts RevisionsContents Setup Mode Server Configuration Troubleshooting and Contact Information Tables ContentsUsing This Guide Purpose and AudienceChapter Summary Additional Documentation Using This GuideIntroduction ApplicationsApplication Examples Introduction Additional Features Configuration MethodsProtocol Support Sample Hardware Address Product Information LabelGetting Started Package ContentsTo install the unit Installing the UDSIP Address Subnet Mask Gateway Required InformationHardware Address IP AddressSelect Assign a specific IP address and click Next Assigning the IP Address DeviceInstallerInstalling DeviceInstaller Assigning an IP AddressAdding the Unit to the Manage List Accessing the UDS1100 Using DeviceInstallerViewing the Current Configuration To view the units current settingsIP Address on Next Step Assigning the IP Address Serial Port LoginGetting Started Accessing UDS1100 Using DeviceInstaller Configuration Using Web-ManagerLantronix Web-Manager Network ConfigurationStatic IP Address Configuration Automatic IP Address ConfigurationServer Configuration Ethernet ConfigurationTo specify how data will be transmitted To configure the UDS1100’s device server settings Server ConfigurationAdvanced Host List Configuration To configure the host listRetry Settings Host Information Channel 1 ConfigurationSerial Settings To configure the channel’s serial settingsPort Settings ChannelPack Control Flush Output Buffer Network to Serial Connection Settings TCPTo configure a channel’s TCP settings Flush Input Buffer Serial to NetworkConnect Protocol Connect Mode Passive ConnectionConnect Mode Active Connection Endpoint ConfigurationCommon Options Connection Settings UDP Disconnect ModeTo configure a channel’s UDP settings UDP Connection Settings Datagram ModeApply Factory Defaults Apply SettingsTo establish a Telnet connection Configuration via Telnet or Serial Port Setup ModeAccessing Setup Mode Telnet ConnectionExiting Setup Mode To exit setup modeSerial Port Connection Set Gateway IP Address Setup Mode Server ConfigurationServer Configuration Option IP AddressNetwork Class Host Bits Netmask Change Telnet Configuration PasswordNetmask Number of Bits for Host Part Dhcp NameSetup Mode Server Configuration Setup Mode Channel Configuration Channel 1 OptionBaudrate Flow Interface ModeMode Option Common I/F Mode Setting BinaryPort Numbers Reserved for Connect ModePort Number Flow Control Option HexIncoming Connection Connect Mode OptionActive Startup ResponseManual Connection Address Example Modem Mode To enable the hostlistDatagram Type No Carrier MessageMeaning ATD Modem Mode Function CommandRemote Port Send the Escape Sequence +++ in Modem ModeAuto Increment Source Port Remote IP AddressDisconnect Mode Option Flush Mode Buffer FlushingOption Pack ControlTrailing Characters DisConnTime Inactivity TimeoutSend Characters Packing IntervalTelnet Terminal Type Channel Port PasswordSetup Mode Advanced Settings Expert Settings OptionTCP Keepalive time in seconds Http Port Number ARP Cache timeout in secondsDisable Monitor Mode at bootup Enable alternate MACSnmp Community Name Security Settings OptionDisable Snmp Disable Telnet SetupDisable Web Setup Disable Tftp Firmware UpdateDisable Port 77FE Hex Disable Web ServerSecurity Settings Defaults Default Settings OptionChannel 1 Configuration Defaults Expert Settings DefaultsSetup Mode Advanced Settings ROM File Firmware UpgradesUsing Tftp Graphical User Interface Obtaining Firmware Reloading FirmwareTo recover firmware Using Tftp Command Line InterfaceFirmware Upgrades Monitor Mode Commands Monitor ModeEntering Monitor Mode Using the Serial Port Entering Monitor Mode Using the Network PortResponse Meaning Command Command Name FunctionLEDs Troubleshooting and Contact InformationProblem/Message Reason Solution Problems and Error MessagesLock on Technical Support Europe, Middle East, and Africa Technical SupportSerial Connector Pinouts Connections and PinoutsSerial Port Modem Cable DB25 Female Interface RS422 4 wire modeNull Modem Cable Lantronix Part No Network PortPower Plug Ethernet Connector PinoutsCategory Description Technical SpecificationsTechnical Specifications AutoIP Alternative Ways to Assign an IP AddressTo assign a temporary IP address ARP and TelnetConverting Binary to Hexadecimal Conversion TableDecimal Binary Hex Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide