Lantronix Comprehensive Guide to UDS1100 Configuration, Default IP, and Manual

Page 32

		4: Configuration Using Web-Manager

	Use Hostlist	If this option is set to True, the device server scrolls through
		the host list until it connects to a device listed in the host list
		table. Once it connects, the unit stops trying to connect to any
		others. If this connection fails, the unit continues to scroll
		through the table until it connects to another IP in the host list.
		The host list is disabled for Manual Mode and for Modem
		Mode. The unit will not accept a data connection from a
		remote device when the host list option is enabled.

	LED	Select Blink for the status LEDs to blink upon connection or
		None for no LED output. The default setting is Blink.

Disconnect Mode

	On Mdm_Ctrl_In Drop	Set to Yes for the network connection to or from the serial port
		to drop when modem_control_in (DSR) transitions from a
		high state to a low state. The default setting is No.

	Hard Disconnect	When set to Yes, the TCP connection closes even if the
		remote site does not acknowledge the disconnect request.

	With EOT	Select Yes to drop the connection when Ctrl-Dor Hex 04 is
		detected. Both Telnet Mode and Disconnect with EOT must
		be enabled for Disconnect with EOT to function properly.
		Ctrl+D is only detected going from the serial port to the
		network. The default setting is No.

	Inactivity Timeout	Use this parameter to set an inactivity timeout. The unit drops
		the connection if there is no activity on the serial line before
		the set time expires. Enter time in the format mm:ss, where m
		is the number of minutes and s is the number of seconds. To
		disable the inactivity timeout, enter 00:00.

3.When you are finished, click the OK button.

4.On the main menu, click Apply Settings.

Connection Settings - UDP

To configure a channel’s UDP settings:

1.On the main menu, click Connection. The Connection Settings window for the selected channel displays.

2.In the available fields, enter or modify the following information:

UDS1100 User Guide

32

Image 32

Contents UDS1100 User Guide Copyright & Trademark ContactsRevisions Date Rev Comments 900-417Contents Setup Mode Server Configuration Troubleshooting and Contact Information Contents TablesChapter Summary Using This GuidePurpose and Audience Using This Guide Additional DocumentationApplication Examples IntroductionApplications Introduction Protocol Support Additional FeaturesConfiguration Methods Product Information Label Sample Hardware AddressPackage Contents Getting StartedInstalling the UDS To install the unitRequired Information Hardware AddressIP Address IP Address Subnet Mask GatewayAssigning the IP Address DeviceInstaller Installing DeviceInstallerAssigning an IP Address Select Assign a specific IP address and click NextAccessing the UDS1100 Using DeviceInstaller Viewing the Current ConfigurationTo view the units current settings Adding the Unit to the Manage ListIP Address on Assigning the IP Address Serial Port Login Next StepGetting Started Configuration Using Web-Manager Accessing UDS1100 Using DeviceInstallerNetwork Configuration Lantronix Web-ManagerAutomatic IP Address Configuration Static IP Address ConfigurationTo specify how data will be transmitted Server ConfigurationEthernet Configuration Advanced To configure the UDS1100’s device server settingsServer Configuration Retry Settings Host List ConfigurationTo configure the host list Channel 1 Configuration Serial SettingsTo configure the channel’s serial settings Host InformationPack Control Port SettingsChannel Connection Settings TCP To configure a channel’s TCP settingsFlush Input Buffer Serial to Network Flush Output Buffer Network to SerialConnect Mode Passive Connection Connect ProtocolCommon Options Connect Mode Active ConnectionEndpoint Configuration To configure a channel’s UDP settings Connection Settings UDPDisconnect Mode Datagram Mode UDP Connection SettingsApply Settings Apply Factory DefaultsConfiguration via Telnet or Serial Port Setup Mode Accessing Setup ModeTelnet Connection To establish a Telnet connectionSerial Port Connection Exiting Setup ModeTo exit setup mode Setup Mode Server Configuration Server Configuration OptionIP Address Set Gateway IP AddressChange Telnet Configuration Password Netmask Number of Bits for Host PartDhcp Name Network Class Host Bits NetmaskSetup Mode Server Configuration Baudrate Setup Mode Channel ConfigurationChannel 1 Option Interface Mode Mode OptionCommon I/F Mode Setting Binary FlowConnect Mode Port NumberFlow Control Option Hex Port Numbers Reserved forConnect Mode Option Incoming ConnectionResponse Active StartupManual Connection Address Example Datagram Type Modem ModeTo enable the hostlist MessageMeaning No CarrierModem Mode Function Command ATDSend the Escape Sequence +++ in Modem Mode Auto Increment Source PortRemote IP Address Remote PortFlush Mode Buffer Flushing Disconnect Mode OptionPack Control OptionDisConnTime Inactivity Timeout Send CharactersPacking Interval Trailing CharactersChannel Port Password Telnet Terminal TypeTCP Keepalive time in seconds Setup Mode Advanced SettingsExpert Settings Option ARP Cache timeout in seconds Disable Monitor Mode at bootupEnable alternate MAC Http Port NumberSecurity Settings Option Disable SnmpDisable Telnet Setup Snmp Community NameDisable Tftp Firmware Update Disable Port 77FE HexDisable Web Server Disable Web SetupDefault Settings Option Channel 1 Configuration DefaultsExpert Settings Defaults Security Settings DefaultsSetup Mode Advanced Settings Firmware Upgrades Using Tftp Graphical User InterfaceObtaining Firmware Reloading Firmware ROM FileUsing Tftp Command Line Interface To recover firmwareFirmware Upgrades Monitor Mode Entering Monitor Mode Using the Serial PortEntering Monitor Mode Using the Network Port Monitor Mode CommandsCommand Command Name Function Response MeaningTroubleshooting and Contact Information LEDsProblems and Error Messages Problem/Message Reason SolutionLock on Technical Support Technical Support Europe, Middle East, and AfricaSerial Port Serial Connector PinoutsConnections and Pinouts DB25 Female Interface RS422 4 wire mode Modem CableNetwork Port Null Modem Cable Lantronix Part NoEthernet Connector Pinouts Power PlugTechnical Specifications Category DescriptionTechnical Specifications Alternative Ways to Assign an IP Address AutoIPARP and Telnet To assign a temporary IP addressDecimal Binary Hex Converting Binary to HexadecimalConversion Table Scientific Calculator Warranty Compliance and Disclaimer Disclaimer and Supplementary Information Index UDS1100 User Guide