GE 68K System manual RZ Zmodem Download

Page 90

	68K System Monitor
GE Energy Services	User's Guide

RZ - ZMODEM Download

Platform

Description

o CPM o D20	o D20 ME	o D20/200	o D20/200 ME	o D25
D20 Base	D20 Base	CCU Base	CCU Base

Use this command to download configuration and application data over the serial port into RAM or FLASH. The 68K Monitor accepts a transfer of ZMODEM binary data to the D25 initiated either by the D25 user or by the sending terminal.

When the transfer is complete, the DOWNLOAD command returns control to 68K Monitor’s command line.

Application code download only works when:

•executing from the BootROM, and

•the monitor has erased the FLASH region.

While the command downloads the file, it recognizes the ZLIB format of the compressed data and uncompresses it.

Syntax		Below is usage and syntax information for this command

		Command Format	rz [/(Vlevel Mtimeout Ctimeout Wwindow)]

		Variables	/Vlevel	verbose level, which determines the level of
				debug messages displayed (default is zero, any
				non-zero value will activate debug messages).
			/Mtimeout	set receive message timeout to the user specified
				value (the default is 2000 ms).
			/Ctimeout	set inter-character timeout to user specified value
				(default is 500 ms).
			/Wwindow	set receiver window size to user specified value
				(default is 1400 bytes).

		Special	Before the start of the download, the system must suspend all
		Considerations	non-protected process running in the system.
			• If there are parameters on the command line, the monitor
			assumes that the D25 initiated the download, and allows 20
			seconds for the user to activate the software that will send
			data to the D25.
			• If there are no parameters, the monitor assumes that the
			sending software initiated the download and it will not
			provide a wait period.
			The command “rz” is the standard prefix used by the
			ZMODEM binary protocol to start a file transfer. A terminal
			using this command can connect to the D25 Monitor and
			simply start sending ZMODEM data without any further user
			input to the D25.


				Continued on next page

			SWM0023 1.00 2		General

3-64	Full Release

Image 90

Contents 68K System Monitor 2002, General Electric Canada Inc. All rights reserved Modification Record Users Guide Table of Contents Erase DstatEcho ETHAbout This Document OverviewPurpose and Audience of this User’s Guide Support Services and Training GEHCalgary.Support@ps.ge.com68K System Monitor Connecting and Using the 68K Monitor D20MES Connecting to the 68K MonitorMonitor D20MEACommand Input and Response Commandname parameters argumentsW l f d address Regular Keyboard Input 68K Monitor Display Error Messages Message Summary Command Grouping General System Commands Diagnostic Commands Memory Commands Process Commands Exchange Commands Breakpoint Commands Configuration Maintenance Commands 68K Monitor Commands Command / Platform Cross-Reference Platform-Specific CommandsList of Commands Monitor Commands AL Change Auto-logout TimerBaud Set Baud Rate Supported data rates, in bps, are Boot Startup Cache Control Cache CAL Calibrate KI For use by qualified programmer onlyCB Clear Breakpoint CCA Change Configuration File Attributes CCB Create Configuration Storage Block Parameters Type ccb 600000 100000 400 2 and press EnterCCF Clear Configuration File Used only when multiple storage regions are definedCF Copy File EpromCLS Clear Screen CP Change Priority CS Check Sum CCU / CcumeMessage Checksum is and should be Dump Memory Syntax DB Define Breakpoint Debug Debug Mode Do you wish to update the Nvram header? y/nIs this data accurate? Y/N Type df /b config.bin and press Enter DF Display File DataDHW Display Hardware Data DIR Directory D25 NvramSpecial Considerations DL Download DM Debug Mode Dstat Decompression Status Edit Memory Address = address to edit in hexadecimal notation Echo Echo Toggle EL Error Log Erase Flash Erase D20 ME / CcumeETH Ethernet Address Exit Exit Fill Memory Type f /w 200000 200400 F034 and press EnterFT Find Table HE or Help Help CCU / Ccume / D25HT Hdlc Test IMG Display Image Information JTF Jump To Flash JX Jam Exchange Type jx 304540 1 2 3 4 and press EnterKIM KI Metrics Move Memory Type m 200000 200400 200 and press EnterPB Print Breakpoint PR Profile Important points to note PRG Program Flash QC Query Configuration Storage Parameters QP Query Process All numeric data displayed is in hexadecimal notation QR Query RAM NvramQX Query Exchange Syntax RB Resume Breakpoint RP Resume Process RR Report RAM Partitions RT RAM Test Type rt /gn 510000 5100b0 25000 and press EnterSyntax RTB Return To BootROM RTC Test CCU RTC RX Request Exchange RZ Zmodem Download RZ Zmodem Download SA Serial Analyzer Buffer overflow SB Step Breakpoint SC Select Active Configuration SET Set System Parameters Very dangerous to use, only for programmersEarlier versions of the Monitor, this command was dhw SI Display System InformationSP Suspend Process This function stops the execution of tasks within the remote ST Serial Test Loop Test SX Send Exchange Type sx 304540 1 2 3 4 and press EnterSysc System Test Invoke Test Tool TxxxTR Trace Type tr /r 20 /t0 10 208000 != 12345678 and press Enter Type tr /r 20 /t0 10 208000 = 12345678 and press EnterType tr /r 20 /t0 10 208000 change and press Enter Type tr /r 20 /t1 10 00123456 and press EnterUL Upload VER Version VP Signal Process Winm WIN Metrics Index KIM