EXP Computer PCMCIA Ethernet Modem Adapter user manual Modem negotiates an error corrected link

Page 29

APPENDIX A

&Q5

Modem negotiates an error corrected link.

&Q6

Select asynchronous operation in normal mode.

&R0

CTS tracks RTS (async) or acts per V.25 (sync).

&R1

CTS is always active.

&S0

DSR is always active.

&S1

DSR acts per V.25.

&T0

Terminate any test in progress.

&T1

Initiate local analog loopback.

&T2

Returns ERROR result code.

&T3

Initiate local digital loopback.

&T4

Allow remote digital loopback.

&T5

Disallow remote digital loopback request.

&T6

Request an RDL without self-test.

&T7

Request an RDL with self-test.

&T8

Initiate local analog loop with self-test.

&V

Display current configurations.

&W0

Store the active profile in NVRAM profile 0.

&W1

Store the active profile in NVRAM profile 1.

&X0

Select internal timing for the transmit clock.

&X1

Select external timing for the transmit clock.

&X2

Select slave receive timing for the transmit clock.

&Y0

Recall stored profile 0 upon power up.

&Y1

Recall stored profile 1 upon power up.

&Zn=x

Store dial string x (to 35) to location n (0 to 3).

%E0

Disable line quality monitor and auto retrain.

%E1

Enable line quality monitor and auto retrain.

%E2

Enable line quality monitor and fallback/fall forward.

%L

Return received line signal level.

%Q

Report the line signal quality.

%TTn

PTT certification test signals.

\G0

Disable modem to modem flow control.

\G1

Enable modem to modem flow control.

\Kn

Controls break handling during three states:

 

When modem receives a break from the DTE:

\K0,2,4

Enter on-line command mode, no break sent to the remote modem.

\K1

Clear buffers and send break to remote modem.

- 25 -

Page 28 Page 30
Image 29
Page 28 Page 30
Contents ThinCom Pcmcia Ethernet Modem Adapter User=s Manual Copyright Table of Contents Register Summary System Requirement IntroductionIntroduction Hardware Installation Guide InstallationInstallation Network Environment Driver selection Installation VerificationInstallation Testing the Network Installation Testing the ModemIf Something Goes Wrong Windows 95 InstallationInstall the Thincom Card Enabling 32-BIT Card Support in Windows Modem Installation VerificationNetwork Installation Data Communication Operation Operating Mode Operating ModeData Communication Remote AccessFile Transferring Cellular OperationFAX Operation FAX OperationPage Diagnostic Function DiagnosticNo Dial Tone TroubleshootingTroubleshooting Appendix a CS.EXE Pcmcs Ctalkcs Basic AT= command for 28,800 Modem Command Function Appendix a Set 10 pps pulse dial with 39%/61% make/break Modem negotiates an error corrected link ECC Comands MNP 10 CommandsCaller ID Commands Enable MNP 10 extended services detection onlyCellular Commands Command Default Function Basic AT= command for 1414 CLConfigured. DTR option Is enabled when DTR is turned onHz guard tone enabled Disabled QAM modulation only42, MNP AT Commands Default Function ATDS=n command = 0, 9, A, B, C, D, #, *, T, P, R, W, @S37000 S90000 S108002 S109062 Range No RetrainEnable Bps rate adjusting Enables V.42 bis only when transmitting data Disables V.42 bisEnables V.42 bis only when receiving data Dial Modifiers Command FunctionCommand Function Return the value of default S register ECC Commands Operating Consideration Function Range Units Register Summary Function Range UnitsFunction Range S33 Xoff Character 255 Appendix B Page FCC Part FCC Compliance StatementsFCC Consumer Information and FCC Requirements Canadian Department of Communications compliance statements Page
Top Page Image Contents