EXP Computer PCMCIA Ethernet Modem Adapter user manual ECC Comands, MNP 10 Commands

Page 30

APPENDIX A

\K3	Send break to remote modem immediately.
\K5	Send break to remote modem in sequence with transmitted data. When modem receives \B in on-line command state:
\K0,1	Clear buffers and send break to remote modem.
\K2,3	Send break to remote modem immediately.
\K4,5	Send break to remote modem in sequence with transmitted data.When modem receives break from the remote modem:
\K0,1	Clear data buffers and send break to DTE.
\K2,3	Send a break immediately to DTE.
\K4,5	Send a break with received data to the DTE.
\N0	Select normal speed buffered mode.
\N1	Select direct mode.
\N2	Select reliable link mode.
\N3	Select auto reliable mode.
\N4	Force LAPM mode.
\N5	Force MNP mode.
+MS	Select modulation
ECC COMANDS
%C0	Disable data compression.
%C1	Enable MNP 5 data compression.
%C2	Enable V.42 bis data compression.
%C3	Enable both V.42 bis and MNP 5 compression.
\A0	Set maximum block size in MNP to 64.
\A1	Set maximum block size in MNP to 128.
\A2	Set maximum block size in MNP to 192.
\A3	Set maximum block size in MNP to 256.
\Bn	Send break of n x 100 ms.
MNP 10 COMMANDS
)M0	Disable MNP 10 link negotiation power adjustment.
)M1	Enable MNP 10 link negotiation power adjustment.
*H0	Select MNP 10 link negotiation at highest rate.
*H1	Select MNP 10 link negotiation at 1200 bps.
*H2	Select MNP 10 link negotiation at 4800 bps.

- 26 -

Image 30

Contents ThinCom Pcmcia Ethernet Modem Adapter User=s Manual Copyright Table of Contents Register Summary Introduction System RequirementIntroduction Installation Hardware Installation GuideInstallation Installation Verification Network Environment Driver selectionInstallation Installation Testing the Modem Testing the NetworkWindows 95 Installation Install the Thincom CardIf Something Goes Wrong Enabling 32-BIT Card Support in Windows Installation Verification ModemNetwork Installation Data Communication Operation Operating Mode Operating ModeFile Transferring Remote AccessData Communication Cellular OperationFAX Operation FAX OperationPage Diagnostic Diagnostic FunctionTroubleshooting TroubleshootingNo Dial Tone Appendix a CS.EXE Pcmcs Ctalkcs Basic AT= command for 28,800 Modem Command Function Appendix a Set 10 pps pulse dial with 39%/61% make/break Modem negotiates an error corrected link MNP 10 Commands ECC ComandsEnable MNP 10 extended services detection only Caller ID CommandsCellular Commands Basic AT= command for 1414 CL Command Default FunctionHz guard tone enabled Is enabled when DTR is turned onConfigured. DTR option Disabled QAM modulation onlyS37000 S90000 S108002 S109062 ATDS=n command = 0, 9, A, B, C, D, #, *, T, P, R, W, @42, MNP AT Commands Default Function Range No RetrainEnable Bps rate adjusting Enables V.42 bis only when receiving data Disables V.42 bisEnables V.42 bis only when transmitting data Dial Modifiers Command FunctionCommand Function Return the value of default S register ECC Commands Operating Consideration Register Summary Function Range Units Function Range UnitsFunction Range S33 Xoff Character 255 Appendix B Page FCC Compliance Statements FCC PartFCC Consumer Information and FCC Requirements Canadian Department of Communications compliance statements Page