EXP Computer PCMCIA Ethernet Modem Adapter user manual Command Function

Page 38

APPENDIX A

 

Basic AT command for 2400, 9600 and 14,400 modem.

Command

Function

A/

Re-execute command.

A

Go off-hook and attempt to answer a call.

B0

Select V.22 connection at 1200 bps.

B1

Select Bell 212A connection at 1200 bps.

C1

Return OK message.

Dn

Dial modifier.

E0

Turn off command echo.

E1

Turn on command echo.

F0

Select auto-detect mode (equivalent to N1).

F1

Select V.21 or Bell 103.

F2

Reserved.

F3

Select V.23 line modulation.

F4

Select V.22 or Bell 212A 1200 bps line speed.

F5

Select V.22 bis line modulation.

F6

Select V.32 bis or V.32 4800 line modulation.

F7

Select V.32 bis 7200 line modulation.

F8

Select V.32 bis or V.32 9600 line modulation.

F9

Select V.32 bis 12000 line modulation.

F10

Select V.32 bis 14400 line modulation.

H0

Initiate a hang-up sequence.

H1

If on-hook, go off-hook and enter command mode.

I0

Report product code.

I1

Report pre-computed checksum from ROM.

I2

Compute checksum and report status.

I3

Report firmware revision, model, and interface type.

I4

Report response programmed by an OEM.

I5

Report the country code number.

I6

Report modem data pump model.

L0

Set low speaker volume.

L1

Set low speaker volume.

L2

Set medium speaker volume.

L3

Set high speaker volume.

M0

Turn speaker off.

M1

Turn speaker on during handshaking and turn speaker off while receiving carrier.

M2

Turn speaker on during handshaking and while receiving carrier.

M3

Turn speaker off during dialing and receiving carrier speaker on during answering.

N0

Turn off automode detection.

N1

Turn on automode detection.

O0

Go on-line.

O1

Go on-line and initiate a retrain sequence.

P

Force pulse dialing.

Q0

Allow result codes to DTE.

Q1

Inhibit result codes to DTE.

Sn

Select S register as default.

Sn?

Return the value of S register n.

=v

Set default S register to value v.

- 34 -

Page 37 Page 39
Image 38
Page 37 Page 39
Contents ThinCom Pcmcia Ethernet Modem Adapter User=s Manual Copyright Table of Contents Register Summary Introduction System RequirementIntroduction Installation Hardware Installation GuideInstallation Installation Verification Network Environment Driver selectionInstallation Installation Testing the Modem Testing the NetworkIf Something Goes Wrong Windows 95 InstallationInstall the Thincom Card Enabling 32-BIT Card Support in Windows Installation Verification ModemNetwork Installation Data Communication Operation Operating Mode Operating ModeFile Transferring Remote AccessData Communication Cellular OperationFAX Operation FAX OperationPage Diagnostic Diagnostic FunctionNo Dial Tone TroubleshootingTroubleshooting Appendix a CS.EXE Pcmcs Ctalkcs Basic AT= command for 28,800 Modem Command Function Appendix a Set 10 pps pulse dial with 39%/61% make/break Modem negotiates an error corrected link MNP 10 Commands ECC ComandsEnable MNP 10 extended services detection only Caller ID CommandsCellular Commands Basic AT= command for 1414 CL Command Default FunctionHz guard tone enabled Is enabled when DTR is turned onConfigured. DTR option Disabled QAM modulation onlyS37000 S90000 S108002 S109062 ATDS=n command = 0, 9, A, B, C, D, #, *, T, P, R, W, @42, MNP AT Commands Default Function Range No RetrainEnable Bps rate adjusting Enables V.42 bis only when receiving data Disables V.42 bisEnables V.42 bis only when transmitting data Dial Modifiers Command FunctionCommand Function Return the value of default S register ECC Commands Operating Consideration Register Summary Function Range Units Function Range UnitsFunction Range S33 Xoff Character 255 Appendix B Page FCC Compliance Statements FCC PartFCC Consumer Information and FCC Requirements Canadian Department of Communications compliance statements Page
Top Page Image Contents