EnGenius Technologies EOC5611P Data Rate, Transmit Power, Antenna, Fragment Length, Distance

Page 28

Data Rate

Select Data Rate from the drop down list. Data rate will affect the efficiency of the

 

throughput. If the data rate is set to a small number, the lower through will get but it

 

can transmit to longer distance.

Transmit Power

Select Transmit Power to increase or decrease Transmit Power. Higher transmit power will sometimes cause unable to connect to the network. On the other hand, the lower transmit power will cause client unable to connect to the device.

Antenna

Select antenna waveform from Diversity, Vertical or Horizontal.

 

 

Fragment Length

Specify package size during transmission. If large amount of client are accessing to

 

the network, specify small number of the fragment length in order to avoid collision.

RTS/CTS Threshold

Specify Threshold package size for RTC/CTS. Using small number of the threshold will cause RTS/CTS packets to be sent more often to consuming more of the available bandwidth. In addition, if the heavy load traffic occurs, the wireless network can be recovered easily from interferences or collisions.

Protection Mode

Select Disable or Enable Protection Mode. If there are large amount of error occur during the transmission, please enable the protect mode otherwise protect mode should remain disable.

WMM

Select Disable or Enable WMM function. WMM is based on the four Access

 

Categories: voice, video, best effort and background. WMM function is not used to

 

guarantee transmission speed.

Channel Bandwidth

Select Channel Bandwidth from the drop down list. Decrease channel bandwidth may cause lower throughput but less collision.

Distance

Specify distance rage between AP and Clients. Longer distance may lose high

 

connection speed.

 

 

Wireless Traffic Shaping

Place a Check to enable Wireless Traffic Shaping function.

 

 

Incoming Traffic Limit

Specify the wireless transmission speed for downloading.

 

 

Outgoing Traffic Limit

Specify the wireless transmission speed for uploading.

 

 

Auction: Changing Wireless Advanced Settings may cause insufficient wireless connection quality. Please remain all settings as default unless you have acknowledged all changing that you have made. Note: The Internal Antenna is only work for 5GHz wireless network. If you would like to use 2.4GHz wireless network, you must connected an External Antenna and switch the antenna types from the bottom of the device (Close to the Ethernet Port).

27

Image 28
Contents EOC5611P Table of Contents Network Configuration Example Feature Product OverviewWireless extensions to Ethernet networks Wired LAN backupTraining/Educational facilities Fully support all types of security typesBenefits System Requirement Package ContentsHardware Overview Red Bad Quality EOC5611P Multi-Function Instruction Guide Access Point Access Point with WDS FunctionClient Bridge WDS BridgeClient Router Computer Settings Assign a Static IP Logging Method Page Wireless Settings Access Point Mode → Wireless Network Wireless Security Save / CancelSuppressed Ssid Station SeparationClient Bridge Mode → Wireless Network WDS Bridge Mode → Wireless Network MAC Address Client Router Mode → Wireless Network Wireless Security Settings 1 WEPWPA-PSK 3 WPA2-PSKWPA-PSK Mixed 5 WPA Radius ServerRadius Port Radius Secret6 WPA2 WPA Mixed Wireless → Wireless Advanced Settings Radius AccountingTransmit Power Protection ModeWireless Traffic Shaping Data RateWireless → Wireless MAC Filter ACL ModeMAC Address Filter AddWireless → WDS Link Settings LAN Settings System → IP SettingsSystem → Spanning Tree Settings Router → WAN Settings Router SettingsWAN Settings → Static IP Internet Connection Type Account NameDomain Name IP Subnet MaskPage Get Automatically From WAN Settings → Dhcp Dynamic IPUse These DNS Servers Apply / Cancel WAN Settings → PPPoE Point-to-Point Protocol over Ethernet LoginPassword Service NameConnect on Demand Keep AliveWAN Settings → Pptp Point-to-Point Tunneling Protocol Pptp Server UsernameRouter → LAN Settings Router → VPN Pass Through Pptp Pass ThroughL2TP Pass Through IPSec Pass ThroughRouter → Port Forwarding Add EntryProtocol Starting PortInformation Status Status → MainPage Status → Wireless Client List Status → System Log Status → WDS Link Status Status → Connection Status Status → Dhcp Client Table Management Settings Management → AdministrationConfirm Password NameRemote Management Remote UpgradePort Management → Management Vlan Management Vlan IDManagement → Snmp Settings Management → Backup/Restore Settings Management → Firmware Upgrade Manually Set Date Time Management → Time SettingsAutomatically Get Date Management → Log SyslogLog Server IP Address Local LogManagement → Diagnostics Network Configuration Example Access PointClient Bridge Mode WDS Bridge ModeWDS Bridge Client Router Vlan Configuration Guide Page Page Page Appendix a FCC Interference Statement Federal Communication Commission Interference Statement