Cypress CY7C1319CV18, CY7C1321CV18, CY7C1317CV18 manual Ieee 1149.1 Serial Boundary Scan Jtag

Page 13

CY7C1317CV18, CY7C1917CV18 CY7C1319CV18, CY7C1321CV18

IEEE 1149.1 Serial Boundary Scan (JTAG)

These SRAMs incorporate a serial boundary scan Test Access Port (TAP) in the FBGA package. This part is fully compliant with IEEE Standard #1149.1-2001. The TAP operates using JEDEC standard 1.8V IO logic levels.

Disabling the JTAG Feature

It is possible to operate the SRAM without using the JTAG feature. To disable the TAP controller, TCK must be tied LOW (VSS) to prevent clocking of the device. TDI and TMS are inter- nally pulled up and may be unconnected. They may alternatively be connected to VDD through a pull up resistor. TDO must be left unconnected. Upon power up, the device comes up in a reset state, which does not interfere with the operation of the device.

Test Access Port—Test Clock

The test clock is used only with the TAP controller. All inputs are captured on the rising edge of TCK. All outputs are driven from the falling edge of TCK.

Test Mode Select (TMS)

The TMS input is used to give commands to the TAP controller and is sampled on the rising edge of TCK. This pin may be left unconnected if the TAP is not used. The pin is pulled up inter- nally, resulting in a logic HIGH level.

Test Data-In (TDI)

The TDI pin is used to serially input information into the registers and can be connected to the input of any of the registers. The register between TDI and TDO is chosen by the instruction that is loaded into the TAP instruction register. For information on loading the instruction register, see the TAP Controller State Diagram on page 15. TDI is internally pulled up and can be unconnected if the TAP is unused in an application. TDI is connected to the most significant bit (MSB) on any register.

Test Data-Out (TDO)

The TDO output pin is used to serially clock data out from the registers. The output is active, depending upon the current state of the TAP state machine (see Instruction Codes on page 18). The output changes on the falling edge of TCK. TDO is connected to the least significant bit (LSB) of any register.

Performing a TAP Reset

A Reset is performed by forcing TMS HIGH (VDD) for five rising edges of TCK. This Reset does not affect the operation of the SRAM and can be performed while the SRAM is operating. At power up, the TAP is reset internally to ensure that TDO comes up in a high-Z state.

TAP Registers

Registers are connected between the TDI and TDO pins to scan the data in and out of the SRAM test circuitry. Only one register can be selected at a time through the instruction registers. Data is serially loaded into the TDI pin on the rising edge of TCK. Data is output on the TDO pin on the falling edge of TCK.

Instruction Register

Three-bit instructions can be serially loaded into the instruction register. This register is loaded when it is placed between the TDI and TDO pins, as shown in TAP Controller Block Diagram on page 16. Upon power up, the instruction register is loaded with the IDCODE instruction. It is also loaded with the IDCODE instruction if the controller is placed in a reset state, as described in the previous section.

When the TAP controller is in the Capture-IR state, the two least significant bits are loaded with a binary “01” pattern to allow for fault isolation of the board level serial test path.

Bypass Register

To save time when serially shifting data through registers, it is sometimes advantageous to skip certain chips. The bypass register is a single-bit register that can be placed between TDI and TDO pins. This enables shifting of data through the SRAM with minimal delay. The bypass register is set LOW (VSS) when the BYPASS instruction is executed.

Boundary Scan Register

The boundary scan register is connected to all of the input and output pins on the SRAM. Several No Connect (NC) pins are also included in the scan register to reserve pins for higher density devices.

The boundary scan register is loaded with the contents of the RAM input and output ring when the TAP controller is in the Capture-DR state and is then placed between the TDI and TDO pins when the controller is moved to the Shift-DR state. The EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions can be used to capture the contents of the input and output ring.

The Boundary Scan Order on page 19 shows the order in which the bits are connected. Each bit corresponds to one of the bumps on the SRAM package. The MSB of the register is connected to TDI, and the LSB is connected to TDO.

Identification (ID) Register

The ID register is loaded with a vendor-specific, 32-bit code during the Capture-DR state when the IDCODE command is loaded in the instruction register. The IDCODE is hardwired into the SRAM and can be shifted out when the TAP controller is in the Shift-DR state. The ID register has a vendor code and other information described in Identification Register Definitions on page 18.

TAP Instruction Set

Eight different instructions are possible with the three-bit instruction register. All combinations are listed in Instruction Codes on page 18. Three of these instructions are listed as RESERVED and must not be used. The other five instructions are described in this section in detail.

Instructions are loaded into the TAP controller during the Shift-IR state when the instruction register is placed between TDI and TDO. During this state, instructions are shifted through the instruction register through the TDI and TDO pins. To execute the instruction once it is shifted in, the TAP controller must be moved into the Update-IR state.

Document Number: 001-07161 Rev. *D

Page 13 of 31

[+] Feedback

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Configurations FeaturesFunctional Description Selection GuideLogic Block Diagram CY7C1917CV18 Logic Block Diagram CY7C1317CV18Doff CLKLogic Block Diagram CY7C1321CV18 Logic Block Diagram CY7C1319CV18BWS Ball Fbga 13 x 15 x 1.4 mm Pinout Pin ConfigurationCY7C1317CV18 2M x CY7C1917CV18 2M xCY7C1321CV18 512K x CY7C1319CV18 1M xPin Name Pin Description Pin DefinitionsSynchronous Read/Write Input. When Power Supply Inputs for the Outputs of the Device Power Supply Inputs to the Core of the DeviceReferenced with Respect to TDO for JtagFunctional Overview Programmable Impedance Depth ExpansionEcho Clocks SRAM#1 ZQ Application ExampleSRAM#2 OperationComments Write Cycle DescriptionsDevice Write cycle description table for CY7C1321CV18 followsInto the device. D359 remains unaltered Device. D80 and D3518 remains unalteredIeee 1149.1 Serial Boundary Scan Jtag Idcode State diagram for the TAP controller follows TAP Controller State DiagramTAP Electrical Characteristics TAP Controller Block DiagramTAP Timing and Test Conditions TAP AC Switching CharacteristicsScan Register Sizes Identification Register DefinitionsInstruction Codes Register Name Bit SizeBit # Bump ID Boundary Scan OrderPower Up Sequence Power Up Sequence in DDR-II SramDLL Constraints DC Electrical Characteristics Electrical CharacteristicsMaximum Ratings Input High Voltage Vref + AC Electrical CharacteristicsInput LOW Voltage Vref Document Number 001-07161 Rev. *D Thermal Resistance CapacitanceParameter Description Test Conditions Max Unit Parameter Description Test Conditions Fbga UnitParameter Min Max DLL Timing Parameter Min Max Output TimesDON’T Care Undefined Switching WaveformsOrdering Information 250 167 Ball Fbga 13 x 15 x 1.4 mm Package DiagramWorldwide Sales and Design Support Products PSoC Solutions Sales, Solutions, and Legal Information

CY7C1321CV18, CY7C1917CV18, CY7C1319CV18, CY7C1317CV18 specifications

Cypress Semiconductor Corporation, a leading provider of advanced embedded memory solutions, offers a series of high-performance SRAM (Static Random Access Memory) devices ideal for a variety of applications. Among these devices are the CY7C1317CV18, CY7C1319CV18, CY7C1917CV18, and CY7C1321CV18. These components are designed to meet the growing demands for non-volatile memory in consumer electronics, automotive systems, telecommunications, and industrial applications.

The CY7C1317CV18 and CY7C1319CV18 are both 256K-bit static RAMs with distinct features. The CY7C1317CV18 offers a dual-port architecture, enabling concurrent access from multiple sources, which substantially enhances performance in data-intensive applications. On the other hand, the CY7C1319CV18 is designed for single-port access, making it ideal for simpler applications that do not require simultaneous data reads and writes.

Further extending Cypress's SRAM portfolio, the CY7C1917CV18 provides a 2M-bit memory configuration with fast access times, high-density storage, and low power consumption. It is particularly well-suited for applications needing quick data retrieval while maintaining efficiency. The architecture of the CY7C1917CV18 allows it to be integrated seamlessly into systems requiring reliable and robust data storage.

Completing the lineup is the CY7C1321CV18, which features an innovative 1M-bit SRAM design. This SRAM is known for its low latency and high speed, making it an excellent choice for high-performance computing applications. It supports a wide operating voltage range and provides a reliable solution for volatile memory needs, especially in fast caching scenarios.

These SRAM devices utilize advanced CMOS technology to achieve high speed and low power characteristics, making them competitive choices in the market. Their robust performance ensures that they satisfy the stringent requirements of various applications, including high-speed networking, graphics processing, and instrumentation.

In terms of reliability, all four devices are built to endure challenging operating conditions and provide excellent data retention. They are offered in compact packages that facilitate easy integration into PCBs, optimizing space and enhancing design flexibility. The combination of performance, low power consumption, and scalability makes Cypress's SRAM products particularly advantageous for next-generation applications across multiple industries.
Top Page Image Contents