Cypress CY7C68013A manual RXD1OUT, INT6, T2EX, GPIFADR8, Slrd, Slwr, RDY2, RDY3, RDY4, RDY5, Flaga

								CY7C68013A, CY7C68014A
								CY7C68015A, CY7C68016A
Table 11. FX2LP Pin Descriptions (continued)
128	100	56	56	56 VF-	Name	Type	Default	Description
TQFP	TQFP	SSOP	QFN	BGA
112	90				PE4 or	IO/Z	I	Multiplexed pin whose function is selected by the
					RXD1OUT		(PE4)	PORTECFG.4 bit.
								PE4 is a bidirectional IO port pin.
								RXD1OUT is an active-HIGH output from 8051 UART1.
								When RXD1OUT is selected and UART1 is in Mode 0,
								this pin provides the output data for UART1 only when
								it is in sync mode. In Modes 1, 2, and 3, this pin is HIGH.
113	91				PE5 or	IO/Z	I	Multiplexed pin whose function is selected by the
					INT6		(PE5)	PORTECFG.5 bit.
								PE5 is a bidirectional IO port pin.
								INT6 is the 8051 INT6 interrupt request input signal. The
								INT6 pin is edge-sensitive, active HIGH.
114	92				PE6 or	IO/Z	I	Multiplexed pin whose function is selected by the
					T2EX		(PE6)	PORTECFG.6 bit.
								PE6 is a bidirectional IO port pin.
								T2EX is an active-HIGH input signal to the 8051 Timer2.
								T2EX reloads timer 2 on its falling edge. T2EX is active
								only if the EXEN2 bit is set in T2CON.
115	93				PE7 or	IO/Z	I	Multiplexed pin whose function is selected by the
					GPIFADR8		(PE7)	PORTECFG.7 bit.
								PE7 is a bidirectional IO port pin.
								GPIFADR8 is a GPIF address output pin.
4	3	8	1	1A	RDY0 or	Input	N/A	Multiplexed pin whose function is selected by the
					SLRD			following bits:
								IFCONFIG[1..0].
								RDY0 is a GPIF input signal.
								SLRD is the input-only read strobe with programmable
								polarity (FIFOPINPOLAR.3) for the slave FIFOs
								connected to FD[7..0] or FD[15..0].
5	4	9	2	1B	RDY1 or	Input	N/A	Multiplexed pin whose function is selected by the
					SLWR			following bits:
								IFCONFIG[1..0].
								RDY1 is a GPIF input signal.
								SLWR is the input-only write strobe with programmable
								polarity (FIFOPINPOLAR.2) for the slave FIFOs
								connected to FD[7..0] or FD[15..0].
6	5				RDY2	Input	N/A	RDY2 is a GPIF input signal.
7	6				RDY3	Input	N/A	RDY3 is a GPIF input signal.
8	7				RDY4	Input	N/A	RDY4 is a GPIF input signal.
9	8				RDY5	Input	N/A	RDY5 is a GPIF input signal.
69	54	36	29	7H	CTL0 or	O/Z	H	Multiplexed pin whose function is selected by the
					FLAGA			following bits:
								IFCONFIG[1..0].
								CTL0 is a GPIF control output.
								FLAGA is a programmable slave-FIFO output status
								flag signal.
								Defaults to programmable for the FIFO selected by the
								FIFOADR[1:0] pins.

Document #: 38-08032 Rev. *L Page 26 of 62

[+] Feedback