Actiontec electronic 56K V.90 manual Lsd

Page 56

BusyTone Detect		Enable	X
LSD	Action	Standard RS232	&C
DTR	Action	Standard RS232	&D

Press any key to continue; ESC to quit.

Option	Selection		AT Cmd
V22b Guard Tone	Disable		&G
Flow Control	Hardware		&K
Error Control Mode	V42, MNP, Buffer		\N
Data Compression	V42bis/MNP5		%C
AutoAnswerRing#	0		S0
AT Escape Char	43		S2
CarriageReturn Char	13		S3
Linefeed Char	10		S4
Backspace Char	8		S5
Blind Dial Pause	2	sec	S6
NoAnswer Timeout	50	sec	S7
“,“ Pause Time	2	sec	S8

Press any key to continue; ESC to quit.

Option	Selection	AT Cmd
No Carrier Disc	2000 msec	S10
DTMF Dial Speed	95 msec	S11
Escape Guard Time	1000 msec	S12
Data Calling Tone	Disabled	S35
Line Rate	33600	S37
DSVD mode	Disabled	-SSE

Stored Phone Numbers

&Z0=

&Z1=

&Z2=

&Z3=

OK

55

Image 56

Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Installing Communications Software Modem’s Voice FeaturesPage Troubleshooting Windows 95/95B/98More Info Panel Does Not Install Windows NT Common Problems No Dialtone ErrorCan’t Connect at 56K Uninstalling the Modem Uninstalling in Windows 95Ltcom.vxd ltwave.inf Page AT Commands Repeat Last CommandAnswer Command ATXnCarrier Control Echo Command DnDialOnline Data Character Echo Command Hook ControlMonitor Speaker Volume Request ID InformationThis command turns the speaker on or off Modulation HandshakeResult Code Control Return On-line to Data ModeSelect Pulse Dialing DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectRecall Stored Profile Busy Tone DetectLong Space Disconnect Auto Retrain Data Carrier Detect DCD Control22bis Guard Tone Control Load Factory SettingsDTR Control Local Flow Control Selection Asynchronous Communications ModeAuxiliary Relay option This Command is effective only for use in Japan View Active Configuration and Stored Profile Data Set Ready DSR OptionLSD Zn=x Store Telephone Number Modem Port Flow Control \An\Bn \Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x Downstream Rate and Control Enable/Disable Data Compression AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line LoopbackATI11 XXX Registers Reference TypeAscii Connection Completion Time-Out Comma Dial Modifier TimeS10 S11 Dtmf Dialing SpeedS22 S14 General Bit Mapped Options StatusS21 S24 Timer to Control Sleep Mode S28 Modulation Enable/DisableS30 Inactivity Timer S32S36 S37 Dial Line Rate defaultS35 Data Calling Tone S43 Auto Mode default 1, range S38 56K Dial Line Rate defaultS42 Auto Rate default 1, range S91 S89 Timer to Control Sleep ModeS90 S92 No CarrierResult Code Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc