Actiontec electronic 56K V.90 manual FCC Regulations, FCC Part 68 Requirements

Page 78

Notices

FCC Regulations

The following statements are provided in accordance with the Federal Communica- tions Commission (FCC) regulations. Please read these statements carefully before installing your modem.

FCC Part 68 Requirements

This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be given to the telephone company.

The REN is used to determine the maximum number of devices connected to your telephone line that will ring in response to an incoming call. In most, but not all, areas, the total REN of devices connected to a line should not exceed five (5.0). To find out the total permitted in your area, contact your local telephone company.

If your telephone equipment causes harm to the telephone network, the telephone company can discontinue your service temporarily. If possible, the company will notify you in advance. But if advance notice isn’t practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.

Your telephone company can make changes in its facilities, equipment, operations, or procedures that could affect the operation of your equipment. If so, you will be notified in advance so you can make the changes needed to maintain uninterrupted service.

If you experience trouble with this equipment, please contact the manufacturer at the address given in this manual. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment in is not malfunctioning.

This equipment may not be used on public coin service provided by the telephone company. Connection to party lines is subject to state tariffs.

Declaration of Conformity

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radio frequency energy and, if

77

Image 78
Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Installing Communications Software Modem’s Voice FeaturesPage Troubleshooting Windows 95/95B/98More Info Panel Does Not Install Windows NT Common Problems No Dialtone ErrorCan’t Connect at 56K Uninstalling the Modem Uninstalling in Windows 95Ltcom.vxd ltwave.inf Page Answer Command AT CommandsRepeat Last Command ATXnCarrier Control Echo Command DnDialOnline Data Character Echo Command Hook ControlMonitor Speaker Volume Request ID InformationThis command turns the speaker on or off Modulation HandshakeReturn On-line to Data Mode Select Pulse DialingResult Code Control DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectBusy Tone Detect Long Space DisconnectRecall Stored Profile Auto Retrain Data Carrier Detect DCD ControlLoad Factory Settings DTR Control22bis Guard Tone Control Asynchronous Communications Mode Auxiliary Relay optionLocal Flow Control Selection This Command is effective only for use in Japan View Active Configuration and Stored Profile Data Set Ready DSR OptionLSD Zn=x Store Telephone Number \An \BnModem Port Flow Control \Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackATI11 XXX Registers Reference TypeAscii S10 Connection Completion Time-OutComma Dial Modifier Time S11 Dtmf Dialing SpeedS14 General Bit Mapped Options Status S21S22 S30 Inactivity Timer S24 Timer to Control Sleep ModeS28 Modulation Enable/Disable S32S37 Dial Line Rate default S35 Data Calling ToneS36 S38 56K Dial Line Rate default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S89 Timer to Control Sleep Mode S90S91 S92 No CarrierResult Code FCC Regulations FCC Part 68 RequirementsDeclaration of Conformity Canadian Department Of Communications Cdoc