Actiontec electronic 56K V.90 manual Windows NT

Page 35

BIOSs don’t allow individual selection of interrupts for ISA, Plug-N-Play, or PCI.) The interrupt settings can be called “ICU”, “ICU/PCI”, “PCI”, or “PNP depending on your BIOS version and manufacturer. Do not set this interrupt to “ISA” only or to “Legacy ISA”. Be sure to Save the settings before exiting the BIOS Setup.

Under some situations, you will find that freeing an interrupt does not solve your installation difficulties. This could be due to another peripheral device stealing the interrupt you just provided. Certain full-featured sound cards require three IRQs to support all their functions. When one becomes available, they take it. This situation requires that you remove your sound card, free an interrupt, install the modem and verify its operation, and then reinstall the sound card. This procedure may also work for sound cards that have lost their sound after the modem has been installed or if the modem will not install in a system with a sound card.

Proceed to “Installing the Modem”.

Windows NT 4.0

Windows NT installation problems are always due to inadequate preparation. The following conditions must be meet before attempting to install the modem or it will not be seen or correctly installed by the system. (See “Do This First” at the beginning of this manual.)

•You must have the latest Windows NT Service Pack installed.

•There must be two IRQ and two I/O port Addresses available for the modem to use.

•The installation utility must be copied from the installation CD-ROM to the default hard drive and extracted.

If you need help on freeing an interrupt or making a COM Port available, see the Windows 95/98 “Does Not Install” section for a discussion of this topic. The “Spe- cial Situations” and “Plug-N-Play BIOS” sections also apply to Windows NT 4.0. See these areas for guidelines. If you are upgrading or removing the drivers, use the installation utility on the Windows NT installation diskette that came with your PCI modem. This utility has an option for removing the modem drivers.

If you are not familiar with changing the settings within your system BIOS setup, you should skip the following system pre-installation procedure and go to “Installing the Modem.” Refer back to this area only if you have a problem installing the mo- dem.

Check your system BIOS IRQ assignments and make sure that at least two interrupts have been assigned to the PCI bus. In your system’s BIOS Setup routine, find the

34

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices to the ModemConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Modem’s Voice Features Installing Communications SoftwarePage Windows 95/95B/98 TroubleshootingMore Info Panel Does Not Install Windows NT No Dialtone Error Common ProblemsCan’t Connect at 56K Uninstalling in Windows 95 Uninstalling the ModemLtcom.vxd ltwave.inf Page ATXn AT CommandsRepeat Last Command Answer CommandCarrier Control DnDial Echo CommandHook Control Online Data Character Echo CommandRequest ID Information Monitor Speaker VolumeModulation Handshake This command turns the speaker on or offResult Code Control Return On-line to Data ModeSelect Pulse Dialing Result Code Option DCE Response FormatDial Tone Detect Extended Result CodesRecall Stored Profile Busy Tone DetectLong Space Disconnect Data Carrier Detect DCD Control Auto Retrain22bis Guard Tone Control Load Factory SettingsDTR Control Local Flow Control Selection Asynchronous Communications ModeAuxiliary Relay option This Command is effective only for use in Japan Data Set Ready DSR Option View Active Configuration and Stored ProfileLSD Zn=x Store Telephone Number Modem Port Flow Control \An\Bn \Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP RegisterATI11 XXX Type Registers ReferenceAscii S11 Dtmf Dialing Speed Connection Completion Time-OutComma Dial Modifier Time S10S22 S14 General Bit Mapped Options StatusS21 S32 S24 Timer to Control Sleep ModeS28 Modulation Enable/Disable S30 Inactivity TimerS36 S37 Dial Line Rate defaultS35 Data Calling Tone S43 Auto Mode default 1, range S38 56K Dial Line Rate defaultS42 Auto Rate default 1, range S91 S89 Timer to Control Sleep ModeS90 No Carrier S92Result Code Declaration of Conformity FCC RegulationsFCC Part 68 Requirements Canadian Department Of Communications Cdoc
Top Page Image Contents