Actiontec electronic 56K V.90 manual S92, No Carrier

Page 76

S92

Direct Connect Transmit Level (default 20)

Sets the transmit level, in dBm for direct connect. This value may have different settings for different phones.

Table 2. The Result Code Summary

Result Code

Description

OK

Command executed

CONNECT

Modem connected to line

RING

A ring signal has been detected

NO CARRIER

Modem lost carrier signal, or does not detect carrier signal, or

 

does not detect answer tone

ERROR

Iinvalid command

CONNECT 1200 EC*

Connection at 1200 bits/s

NO DIALTONE

No dial tone detected

BUSY

Busy signal detected

NO ANSWER8

No quiet answer

CONNECT 2400 EC*

Connection at 2400 bits/s

CONNECT 4800 EC*

Connection at 4800 bits/s

CONNECT 9600 EC*

Connection at 9600 bits/s

CONNECT 14400 EC*

Connection at 14400 bits/s

CONNECT 19200 EC*

Connection at 19200 bits/s

CONNECT 7200 EC*

Connection at 7200 bits/s

CONNECT 12000 EC*

Connection at 12000 bits/s

CONNECT 16800 EC*

Connection at 16800 bits/s

CONNECT 300 EC*

Connection at 300 bits/s

CONNECT 21600 EC*

Connection at 21600 bits/s

CONNECT 24000 EC*

Connection at 24000 bits/s

CONNECT 26400 EC*

Connection at 26400 bits/s

CONNECT 28800 EC*

Connection at 28800 bits/s

CONNECT 31200 EC*

Connection at 31200 bits/s

CONNECT 33600 EC*

Connection at 33600 bits/s

CONNECT 38400 EC*

Connection at 38400 bits/s

CONNECT 57600 EC*

Connection at 57600 bits/s

CONNECT 115200 EC

Connection at 115200 bits/s

DELAYED

Delay is in effect for the dialed number

BLACKLISTED

Dialed number is blacklisted

BLACKLIST FULL

Blacklist is full

CONNECT 32000 EC*

Connection at 32000 bits/s, 56K rate

CONNECT 34000 EC*

Connection at 34000 bits/s, 56K rate

CONNECT 36000 EC*

Connection at 36000 bits/s, 56K rate

CONNECT 38000 EC*

Connection at 38000 bits/s, 56K rate

CONNECT 40000 EC*

Connection at 40000 bits/s, 56K rate

CONNECT 42000 EC*

Connection at 42000 bits/s, 56K rate

CONNECT 44000 EC*

Connection at 44000 bits/s, 56K rate

CONNECT 46000 EC*

Connection at 46000 bits/s, 56K rate

CONNECT 48000 EC*

Connection at 48000 bits/s, 56K rate

CONNECT 50000 EC*

Connection at 50000 bits/s, 56K rate

CONNECT 52000 EC*

Connection at 52000 bits/s, 56K rate

CONNECT 54000 EC*

Connection at 54000 bits/s, 56K rate

CONNECT 56000 EC*

Connection at 56000 bits/s, 56K rate

CONNECT 58000 EC*

Connection at 58000 bits/s, 56K rate

75

Page 75 Page 77
Image 76
Page 75 Page 77
Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Installing Communications Software Modem’s Voice FeaturesPage Troubleshooting Windows 95/95B/98More Info Panel Does Not Install Windows NT Common Problems No Dialtone ErrorCan’t Connect at 56K Uninstalling the Modem Uninstalling in Windows 95Ltcom.vxd ltwave.inf Page AT Commands Repeat Last CommandAnswer Command ATXnCarrier Control Echo Command DnDialOnline Data Character Echo Command Hook ControlMonitor Speaker Volume Request ID InformationThis command turns the speaker on or off Modulation HandshakeSelect Pulse Dialing Return On-line to Data ModeResult Code Control DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectLong Space Disconnect Busy Tone DetectRecall Stored Profile Auto Retrain Data Carrier Detect DCD ControlDTR Control Load Factory Settings22bis Guard Tone Control Auxiliary Relay option Asynchronous Communications ModeLocal Flow Control Selection This Command is effective only for use in Japan View Active Configuration and Stored Profile Data Set Ready DSR OptionLSD Zn=x Store Telephone Number \Bn \AnModem Port Flow Control \Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x Downstream Rate and Control Enable/Disable Data Compression AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line LoopbackATI11 XXX Registers Reference TypeAscii Connection Completion Time-Out Comma Dial Modifier TimeS10 S11 Dtmf Dialing SpeedS21 S14 General Bit Mapped Options StatusS22 S24 Timer to Control Sleep Mode S28 Modulation Enable/DisableS30 Inactivity Timer S32S35 Data Calling Tone S37 Dial Line Rate defaultS36 S42 Auto Rate default 1, range S38 56K Dial Line Rate defaultS43 Auto Mode default 1, range S90 S89 Timer to Control Sleep ModeS91 S92 No CarrierResult Code FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc
Top Page Image Contents