Actiontec electronic 56K V.90 manual Canadian Department Of Communications Cdoc

Page 79

not installed and used in accordance with the instructions, may cause harmful inter- ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio and television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CAUTION: CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Canadian Department Of Communications (CDOC)

Requirements for End Users:

Notice: The Canadian Department of Communications label identifies certified equip- ment. This certification means the equipment meets certain telecommunications network requirements. The Department does not guarantee the equipment will op- erate to the user’s satisfaction.

Before installing this equipment users should ensure that connection to the line is allowed by the local telecommunications company. The equipment must also be in- stalled using an acceptable method of connection. In some cases, the company’s in- side wiring associated with a single line individual service may be extended by means of a telephone extension cord. Compliance with the above conditions may not pre- vent degradation of service in certain situations.

Repairs to certified equipment should be made by an authorized Canadian mainte- nance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

78

Image 79
Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices to the ModemConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Modem’s Voice Features Installing Communications SoftwarePage Windows 95/95B/98 TroubleshootingMore Info Panel Does Not Install Windows NT No Dialtone Error Common ProblemsCan’t Connect at 56K Uninstalling in Windows 95 Uninstalling the ModemLtcom.vxd ltwave.inf Page ATXn AT CommandsRepeat Last Command Answer CommandCarrier Control DnDial Echo CommandHook Control Online Data Character Echo CommandRequest ID Information Monitor Speaker VolumeModulation Handshake This command turns the speaker on or offSelect Pulse Dialing Return On-line to Data ModeResult Code Control Result Code Option DCE Response FormatDial Tone Detect Extended Result CodesLong Space Disconnect Busy Tone DetectRecall Stored Profile Data Carrier Detect DCD Control Auto RetrainDTR Control Load Factory Settings22bis Guard Tone Control Auxiliary Relay option Asynchronous Communications ModeLocal Flow Control Selection This Command is effective only for use in Japan Data Set Ready DSR Option View Active Configuration and Stored ProfileLSD Zn=x Store Telephone Number \Bn \AnModem Port Flow Control \Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass ThroughV90=x Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP RegisterATI11 XXX Type Registers ReferenceAscii S11 Dtmf Dialing Speed Connection Completion Time-OutComma Dial Modifier Time S10S21 S14 General Bit Mapped Options StatusS22 S32 S24 Timer to Control Sleep ModeS28 Modulation Enable/Disable S30 Inactivity TimerS35 Data Calling Tone S37 Dial Line Rate defaultS36 S42 Auto Rate default 1, range S38 56K Dial Line Rate defaultS43 Auto Mode default 1, range S90 S89 Timer to Control Sleep ModeS91 No Carrier S92Result Code FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc