Actiontec electronic 56K V.90 manual Xxx

Page 67

Description

Example

Comments

Final Transmit Carrier Rate

33600

The last upload connection rate.

Final Receive Carrier Rate

33600

The last download connection rate.

Protocol Negotiation Result

V.42

Possible results are: V.42, MNP or noEC

Data Compression Result

V.42bis

Possible results are: V.42bis, MNP5 or no

 

 

Compression.

Estimated Noise Level

10

An average of the squared error between the

 

 

received constellation point and the decision

 

 

point.

Receive Signal Power Level

20

Receive signal (-dBm)

Transmit Signal Power Level

10

Transmit signal level ( –dBm)

Round Trip Delay (msec)

60

Measured Round Trip Delay in milliseconds

Near Echo Level (-dBm)

39

Measured Near Echo Level

Far Echo Level (-dBm)

60

Measured Far Echo Level

Transmit Frame Count

5000

Number of HDLC frames transmitted.

Transmit Frame Error Count

10

Number of frame errors transmitted

Receive Frame Count

5000

Number of HDLC frames received.

Receive Frame Error Count

10

Number of frame errors received

Retrain and Rate Negotiate Event

1

Number of retrains initiated by the local mo-

 

 

dem.

Retrain and Rate Negotiate Event

1

Number of retrains initiated by the by remote

 

 

modem.

Call Termination Cause

0

0 -Call Terminated by Local modem

 

 

1 -Call Terminated by Remote modem

 

 

2 -No Answer - the Remote modem did not

 

 

answer

 

 

3 -Training Failure - the modems failed to ne-

 

 

gotiate V.34 or 56K protocols.

 

 

4 -Protocol Failure - the modems failed to ne-

 

 

gotiate V.42 protocol.

Robbed-Bit Signaling (56K only)

6

The number of robbed bits detected.

Digital Loss

0

Digital Loss in dB.

Remote Server ID

XXX

ID number of remote server.

66

Image 67
Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction Do This First For Windows 95 and Windows 98 InstallationsFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices to the ModemConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Modem’s Voice Features Installing Communications SoftwarePage Windows 95/95B/98 TroubleshootingMore Info Panel Does Not Install Windows NT No Dialtone Error Common ProblemsCan’t Connect at 56K Uninstalling in Windows 95 Uninstalling the ModemLtcom.vxd ltwave.inf Page ATXn AT CommandsRepeat Last Command Answer CommandCarrier Control DnDial Echo CommandHook Control Online Data Character Echo CommandRequest ID Information Monitor Speaker VolumeModulation Handshake This command turns the speaker on or offSelect Pulse Dialing Return On-line to Data ModeResult Code Control Result Code Option DCE Response FormatDial Tone Detect Extended Result CodesLong Space Disconnect Busy Tone DetectRecall Stored Profile Data Carrier Detect DCD Control Auto RetrainDTR Control Load Factory Settings22bis Guard Tone Control Auxiliary Relay option Asynchronous Communications ModeLocal Flow Control Selection This Command is effective only for use in Japan Data Set Ready DSR Option View Active Configuration and Stored ProfileLSD Zn=x Store Telephone Number \Bn \AnModem Port Flow Control \Kn Same as 4.Default \Nn \Vn Protocol Result Code \Tn Inactivity TimerData Calling Tone \Xn XON/XOFF Pass Through V90=x Downstream Rate and Control Line-to-Line Loopback Enable/Disable Data CompressionAT Commands for Testing and Debugging Write to/Read from DSP RegisterATI11 XXX Type Registers ReferenceAscii S11 Dtmf Dialing Speed Connection Completion Time-OutComma Dial Modifier Time S10S21 S14 General Bit Mapped Options StatusS22 S32 S24 Timer to Control Sleep ModeS28 Modulation Enable/Disable S30 Inactivity TimerS35 Data Calling Tone S37 Dial Line Rate defaultS36 S42 Auto Rate default 1, range S38 56K Dial Line Rate defaultS43 Auto Mode default 1, range S90 S89 Timer to Control Sleep ModeS91 No Carrier S92Result Code FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc