Actiontec electronic 56K V.90 manual An, Bn, Modem Port Flow Control

Page 58

\An

Select Maximum MNP Block Size

The modem will operate an MNP error corrected link using a maximum block size controlled by the parameter supplied.

Command

Effect

 

 

\AO

64 characters

 

 

\A1

128 characters

 

 

\A2

192 characters

 

 

\A3

256 characters (Default)

 

 

Result Codes:

OK

n = 0, 1, 2, 3

 

 

ERROR

Otherwise

 

 

\Bn

Transmit Break to Remote

In non-error correction mode, the modem will transmit a break signal to the remote modem with a length in multiples of 100ms according to parameter specified. The command works in conjunction with the \K command.

 

Command

Effect

 

 

 

 

\B1-\B9

Break length in 100ms units. (Default = 3.) (Non-error

 

corrected mode only.)

 

 

 

 

 

Result Codes:

 

 

 

 

 

OK

If connected in data modem mode.

 

 

 

 

NO CARRIER

If not connected or connected in fax modem mode.

 

 

 

\G

Modem Port Flow Control

 

 

 

 

Command

Effect

 

 

 

 

\G0

Returns an “OK” for compatibility (default).

 

 

 

 

\G1

NOT SUPPORTED responds ERROR.

 

 

 

57

Image 58
Contents 56K V.90 PCI Voice/Fax Windows Modem Table of Contents Introduction For Windows 95 and Windows 98 Installations Do This FirstFor Windows NT 4.0 Installation For Windows 2000 Professional Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95B Page Configuring Windows Page Next Page Page Configuring Windows NT Page Page Page Configuring Windows 2000 Professional Page Page Page Page Confirming the Installation of the Driver in Windows Page Installing Communications Software Modem’s Voice FeaturesPage Troubleshooting Windows 95/95B/98More Info Panel Does Not Install Windows NT Common Problems No Dialtone ErrorCan’t Connect at 56K Uninstalling the Modem Uninstalling in Windows 95Ltcom.vxd ltwave.inf Page Answer Command AT CommandsRepeat Last Command ATXnCarrier Control Echo Command DnDialOnline Data Character Echo Command Hook ControlMonitor Speaker Volume Request ID InformationThis command turns the speaker on or off Modulation HandshakeSelect Pulse Dialing Return On-line to Data ModeResult Code Control DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectLong Space Disconnect Busy Tone DetectRecall Stored Profile Auto Retrain Data Carrier Detect DCD ControlDTR Control Load Factory Settings22bis Guard Tone Control Auxiliary Relay option Asynchronous Communications ModeLocal Flow Control Selection This Command is effective only for use in Japan View Active Configuration and Stored Profile Data Set Ready DSR OptionLSD Zn=x Store Telephone Number \Bn \AnModem Port Flow Control \Kn Same as 4.Default \Nn \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Data Calling ToneV90=x Downstream Rate and Control Write to/Read from DSP Register Enable/Disable Data CompressionAT Commands for Testing and Debugging Line-to-Line LoopbackATI11 XXX Registers Reference TypeAscii S10 Connection Completion Time-OutComma Dial Modifier Time S11 Dtmf Dialing SpeedS21 S14 General Bit Mapped Options StatusS22 S30 Inactivity Timer S24 Timer to Control Sleep ModeS28 Modulation Enable/Disable S32S35 Data Calling Tone S37 Dial Line Rate defaultS36 S42 Auto Rate default 1, range S38 56K Dial Line Rate defaultS43 Auto Mode default 1, range S90 S89 Timer to Control Sleep ModeS91 S92 No CarrierResult Code FCC Part 68 Requirements FCC RegulationsDeclaration of Conformity Canadian Department Of Communications Cdoc